Where Can You Buy A 1000 Gallon Septic Tank? (Best solution)

How much sand is needed to fill 1000 gallon tank?

  • For a 500 – gallon tank you will need 4-5 tons of “Grade A” sand and for a 1000 gallon tank you will need 8-10 ton of “Grade A” sand – which can be bought/found at The Alton Sand Plant. They refer to this sand as 801B-FA1.

How much does a 1000 gallon holding tank cost?

How much does a 1000 gallon concrete septic tank cost? Answer: The average retail cost for a 1000 gallon concrete septic tank is $1062.50.

What is the smallest septic system you can buy?

If you’re looking to install a septic system, the smallest tank size you’re likely to find is 750-gallon, which will accommodate one to two bedrooms. You can also opt for a 1,000-gallon system, which will handle two to four bedrooms.

What is the alternative to a septic tank?

Mound systems work well as alternatives to septic tanks when the soil around your home or building is too dense or too shallow or when the water table is too high. Although they are more expensive and require more maintenance than conventional systems, mound systems are a common alternative.

Can you have a septic tank without a leach field?

The waste from most septic tanks flows to a soakaway system or a drainage field. If your septic tank doesn’t have a drainage field or soakaway system, the waste water will instead flow through a sealed pipe and empty straight into a ditch or a local water course.

How long does it take to fill a 1000 gallon septic tank?

Therefore, it will take about 5 years for one adult to fill 300 gallons of a 1,000-gallon septic tank with sludge and scum. A family of four will fill the 300-gallon storage volume of a 1,000-gallon septic tank in about 1.5 years.

How big of a septic tank do I need?

The larger your home, the larger the septic tank you’re going to need. For instance, a house smaller than 1,500 square feet usually requires a 750 to 1,000-gallon tank. On the other hand, a bigger home of approximately 2,500 square feet will need a bigger tank, more than the 1,000-gallon range.

What size septic tank do I need for a tiny house?

Tiny homes typically require a 500 to 1,000-gallon septic tank. Though, it’s not always possible to implement a tank of this size. In some states, for example, the minimum tank size is 1,000 gallons. There may be exceptions to this rule if your home is on wheels.

How much does it cost to pump a septic tank?

How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

Is concrete septic tank better than plastic?

Cement Septic tanks are very durable than plastic tanks and, if kept properly, can have extended longevity. With regular draining and proper maintenance, a cement septic tank can last for up to 40 years. Cement septic tanks are resistant to environmental changes such as tree roots or changing soil conditions.

Buy 1,000 Gal. Plastic Septic Tank

Septic tanks for sale in the 1000 gallon capacity are available for purchase at the most competitive costs online.

Tank / Capacity Length Width Height Size Compartments Part From Price
1000 Gallon Septic Tank 101″ 60″ 60″ 101″ L 60″ W 60″ H 1 AST-1000-1 IA $1,692
1000 Gallon Septic Tank 101″ 60″ 60″ 101″ L 60″ W 60″ H 2 AST-1000-2 IA $1,852
1000 Gallon Septic Tank 101″ 52″ 71″ 101″ L 52″ W 71″ H 1 44622 MN, OH $0
1000 Gallon Septic Tank 102″ 60″ 63″ 102″ L 60″ W 63″ H 1 41718 GA, MN, MS, NY, OH, OK, UT, WA $1,922
1000 Gallon Septic Tank 102″ 60″ 63″ 102″ L 60″ W 63″ H 2 41720 GA, MN, MS, NY, OH, OK, UT, WA $2,020
1000 Gallon Septic Tank 102″ 60″ 63″ 102″ L 60″ W 63″ H 2 41721 CA $2,020
1000 Gallon Above Ground Septic Holding Tank 136″ 91″ 20″ 136″ L 91″ W 20″ H No 1000GB MS $2,400
1000 Gallon Low Profile Septic TankShips Fast! ~ 48 Hour Lead Time 127″ 60″ 51″ 127″ L 60″ W 51″ H 1 42405 GA, MN, OH, OK, UT, WA $1,679
1000 Gallon Low Profile Septic Tank 127″ 60″ 51″ 127″ L 60″ W 51″ H 2 43517 GA, MN, OH, OK, UT, WA $1,794
1000 Gallon Low Profile Septic Tank – Intended For Use In IL 127″ 60″ 51″ 127″ L 60″ W 51″ H 1 43538 OH $1,679
1000 Gallon Low Profile Septic Tank – Intended For Use In IL 127″ 60″ 51″ 127″ L 60″ W 51″ H 2 43541 OH $1,794
1000 Gallon Low Profile Septic Tank – IAPMO Approved 127″ 60″ 51″ 127″ L 60″ W 51″ H 2 44482 CA $1,903
1000 Gallon Low Profile Septic Tank – NC/SC Approved 127″ 60″ 51″ 127″ L 60″ W 51″ H 2 43510 GA $1,794
1050 Gallon Low Profile Septic Tank – FL Approved 127″ 60″ 51″ 127″ L 60″ W 51″ H 2 43533 FL $2,108

1000 Gallon Low Profile Septic Tank

Dimensions 127″ Length x 60″ Width x 51″ Height Liquid Access 1 Inlet, 1 Outlet, 2 Manway / Lid Inlet 1 4″ Gasketed PVC Tee Assembly Outlet / Drain 1 4″ Gasketed PVC Tee Assembly Preplumbed Pre-drilled with loose GasketTee Septic State Approved Use Alabama, Arkansas, Arizona, Colorado, Connecticut, Delaware, Georgia, Iowa, Idaho, Illinois, Indiana, Kansas, Kentucky, Louisiana, Massachusetts, Maryland, Maine, Michigan, Minnesota, Missouri, Mississippi, Montana, North Carolina, North Dakota, Nebraska, New Hampshire, New Jersey, New Mexico, Nevada, New York, Ohio, Oklahoma, Oregon, Pennsylvania, Rhode Island, South Carolina, South Dakota, Tennessee, Texas, Utah, Virginia, Vermont, Washington, Wisconsin, West Virginia, Wyoming Shipping Locations Georgia, Minnesota, Ohio, Oklahoma, Utah, Washington Shipping Zip Codes 30224, 43130, 55375, 74801, 84074, 98671

1000 Gallon 2 Compartment Plastic Septic Tank (Preplumbed)

The following items are included in the 2-compartment septic tank: Septic tanks manufactured by Norwesco are one-piece construction, which eliminates the need for further assembly and so reduces installation time and labor.

  • Rugged, one-piece tank that is rotationally molded and does not have any seams to leak
  • During the installation process, there is no need for any specific backfill or water filling. During pump-outs, it is possible to pump the water out completely. It is possible to install with 6″ to 36″ of cover
  • A septic tank or pump tank that can also be used for non-potable water is suitable for this use. Openings and lids for access are compatible with Norwesco manhole extensions, double-wall corrugated pipe, and ribbed PVC pipe.

Disclaimer: This tank is intended for usage below ground only.

State RequirementsApprovals

Our tanks must comply with a variety of health code standards that are in place across the United States. These codes are governed by the state or county in which you live, depending on your location. Please speak with your local health agency for assistance in choosing the tank you require.

Installation Video: (This tank already had plumbing installed when tank arrives)

  • If you ask the question, no, you cannot place the plastic septic tank beneath a driveway since it is not authorized, and doing so will invalidate the guarantee. Keep tanks out of the line of heavy and vehicle traffic regions, and don’t put them beneath driveways. It is advised that bedding/backfill be made up of an equal mixture of sand and gravel (often known as “pea gravel”). 2. Is it necessary to mix the sand and gravel? 3. Is it possible to utilize a septic tank above ground? Underground plastic septic tanks are intended for use solely below ground. They are not intended for above ground usage. The use of above-ground storage tanks may result in the tank’s distortion and degradation. When compared to underground storage tanks, it is significantly more cost-effective to employ an above-ground storage tank that has been particularly constructed for above-ground uses. Is it possible to keep hot water in plastic septic tanks? Yes, but only if the water temperature is not greater than 100 degrees Fahrenheit
  • Polyethylene storage tanks have a maximum storage temperature of 120 degrees Fahrenheit. Containments with a temperature greater than 120 degrees Fahrenheit, even for a short period of time, might degrade the structural integrity of the tank and making it more prone to deformation and collapse
  • What is the best method of accessing an underground plastic septic tank? Each underground plastic septic tank is supplied with a manhole access hatch. Additionally, risers can be placed to the top of the tank to provide for access from the ground level. A riser would save you from having to dig up the dirt above the manway in order to get access
  • Otherwise, 6. Is it possible to pick up a plastic septic tank in the area? In most circumstances, yes. You must place an order in advance in order to pick up a plastic septic tank and save money on shipping. When you are notified that your tank is ready for pickup, Plastic-mart will issue you with a six-digit trip number that will allow you to go and pick up your tank Monday through Friday from 8:30 a.m. to 2:30 p.m. Likewise, Plastic-mart and the local producers are grateful for the chance to supply local pick as well as the collaboration necessary to ensure that the process runs well. Important Note: Oklahoma tanks are shipped within 14 days of order placement. Please contact us to inquire about the availability of other locations.
See also:  What Is An Underground Storage Tank Septic Tceq -Petroleum? (Solved)

1000 Gallon Septic Tanks

Our 1000 gallon septic tank, which is constructed of precast concrete, has a capacity of 1000 gallons of liquid capacity. With this mid-seam design concrete septic tank, you may connect the pipe from the home to either one of the tank’s side or center inlets, depending on your preference. The same choice is accessible at the tank’s outlet, whether it is exiting to the leach field from the tank’s side or exiting from the tank’s central outlet. To connect the pipe entering and exiting the precast construction, Polylok IV closed-end boots are utilized.

ASTM C 1227NPCA is fully compliant with all best-practice criteria.

1000 Gallon Septic Tank DimensionsDetails
Tank dimensions 8’ x 5’8” x 5’2”
Number of bedrooms supported Formerly 2 Now used as a pump station, holding tank, or adding to an existing system
Pre-assembled Yes
Ideal for high water table No, but our 1000 gallon monolithic septic tank is.
Average retail cost $1062.50
Number of covers (lids) 2
Can come in traffic rated (H20) capacity Yes
Concrete strength 5,000 PSI
What are its gallons per vertical inch 21
Weight 8,600 lbs.
Fiber re-enforced Yes
Number of inlets boots (Up to schedule 40pipe can slide through) 3
Height of inlet from bottom of tank to bottom of pipe 51”
Number of outlets boots (Up to schedule 40 pipe can slide through) 3
Height of outlet from bottom of tank to bottom of pipe 48”
Required height of inlet baffle (20% of liquid level) 9”
Required height of outlet baffle (40% of liquid level) 18”

Frequently Asked Questions

In response to your question, the typical retail price for a 1000-gallon concrete septic tank is $1062.55.

What is the most common septic tank size?

Answer:It is a 1000 gallon septic tank across the United States, however it is rarely utilized as a septic tank in New Hampshire. By updating the state standards in 2012, the Department of Subsurface (DES) effectively rendered it no longer applicable as a stated tank size in New Hampshire. They are currently being utilized as a pump station, holding tank, or to increase the capacity of an existing septic system, among other things.

Is it ideal for high water table properties?

A monolithic septic tank is recommended for locations with high water tables since the seam is located at the very top of the septic tank, rather than at the bottom. Mid-seam and monolithic types of 1000 gallon septic tanks are both available from Septic Tanks Direct.

How much does a 1000 gallon concrete septic tank weigh?

Answer:Our 1000 gallon tanks weigh around 8,600 lbs, although the weight of precast tanks varies significantly across manufacturers based on the specifications, wall thickness, floortop thickness, and rebar reinforcement used in the construction.

How deep is a 1000 gallon septic tank?

Septic tanks made of concrete are generally 4′ 8″ deep and hold 1,000 gallons of water.

How many bedrooms does a 1000 gallon septic tank support?

Answer:In New Hampshire, the minimum need used to be many, then two, and currently a 1250 gallon septic tank is the bare essential. In New Hampshire, a 1000-gallon tank is currently often utilized as a holding tank or pump station, or to increase the capacity of an existing septic system.

Can you drive over a 1000 gallon septic tank?

It is determined by the design rating.

We make it in three different configurations: H-10 is designed for pedestrian activity and has a live load of 300 pounds per square foot plus a burial depth of 3 feet. HD is intended for burial depths up to 5 feet. H-20 is designed for drive-over traffic and burial depths up to 6 feet.

1000 Gallon Septic Tank Dimensions, Features/Details*

  • In two-bedroom installations, a 1000-gallon septic tank is utilized. This structure is frequently used as a pump station. For many years, the standard size in New Hampshire was the same as the standard size in Maine. This is the smallest size that may be used as a grease trap and is suggested for this application. It is shipped pre-assembled to make installation as simple as possible

* Standards for the state of New Hampshire are displayed; click here for information on other states’ specifications. You might also be interested in these widely used precast concrete septic tanks if you like what you see.

  • Septic Tanks: Precast Concrete Septic Tank – 1250 Gallons
  • Precast Concrete Septic Tank – 1250 Gallons Monolithic
  • Precast Concrete Septic Tank – 1500 Gallons Monolithic
  • Precast Concrete Septic Tank – 1600 Gallons
  • Precast Concrete Septic Tank – 1600 Gallons Monolithic
  • Precast Concrete Septic Tank – 2000 Gallons
  • Precast Concrete Septic Tank – 2000 Gallons Monolithic
  • Precast Concrete Septic Tank – 1025

a little about the author: The Andrew J. Foss, Inc. precast concrete firm was founded by my father in 1963 when he was just 19 years old. My precast education began at a very young age for myself. Everything I know about producing high-quality precast concrete goods, from septic tanks to concrete headwalls, was passed down to me by him. He also taught me that in order to be successful in business, you must provide a superior product and treat your customers the way you would like to be treated yourself.

Plastic Septic Tanks – Two Compartments

Ace Septic TanksAce Roto-Mold septic tanks are stronger, easier to install, and less costly than old-fashioned concrete septic tanks- yet they still offer the quality construction and safety you expect. Manufactured from high-density polyethylene with U.V. inhibitors, Ace Roto-Mold tanks utilize a horizontal flow designed for below ground installations up to 36 inches. Ace Tanks are IAPMO approved and have passed strenuous stress tests. Each tank carries an individual serial code and is fully document from date of manufacture.Ace Roto-Mold septic tanks are designed and manufactured with rigorous quality controls. The trapezoidal deep-rib design and interior baffle system make Ace Tanks the industry choice. Only Ace tanks feature a custom-molded gasket in the lid. Manufactured from extruded Nitrile rubber, the gasket snaps into the lid and ensures a watertight seal. Our exclusive lid design locks in place with nylon ties, eliminating the need for metal fasteners that can corrode and fail.Ace’s unique tank baffle system slows the flow of wastewater and directs it to the middle of the tank so wastewater can separate from solids. An outlet baffles allows the partially treated liquids to flow out for further treatment. Advantages of Ace’s baffle design include added strength, versatility, and ease of installation.Septic tanks are available in one-compartment and two-compartment designs and are manufactured for containment of liquids up to 1.7 specific gravity.Ace Septic / Cistern Tank AccessoriesRemember to order your state specific internal plumbing kit. Links:Septic Tank Product Description, Function and ServiceSeptic Tank Installation ProceduresSpherical Septic Tank Installation ProceduresSeptic Tank Divider Installation Procedures

Norwesco Septic Tanks300 + 500 Gallon Spheres may be used as Septic Holding Tanks (Pump Out).SeeUnderground Water Tanksfor others availablefor Septic Holding Tanks.The world’s leading manufacturer of polyethylene tanks, NORWESCO has been producing polyethylene septic tanks since 1980. With that kind of experience, NORWESCO offers you proven products that you can count on for years of dependable, trouble-free service.For septic system replacement and new home construction, NORWESCO‘s polyethylene septic tanks are designed for durability and quick, easy installation. Any NORWESCO septic tank can be transported to the job site in a pickup truck and carried by just two people. That enables you to install the tank on your schedule.All NORWESCO septic tanks are manufactured by means of the rotational molding process, which produces a one-piece, seamless, watertight tank. Polyethylene is unaffected by soil chemicals and by the chemicals and gases present in sewage, so NORWESCO septic tanks will not rust or corrode and require no additional coatings as other tanks do. NORWESCO’s strict quality guidelines ensure an environmentally safe septic tank.NORWESCO septic tanks come equipped with manhole covers and detailed installation procedures. Manhole extensions and lid/riser combinations are available to bring tank access to grade and to meet code specifications. The 750, 1000, 1250 and 1500 gallon sizes are available in both one and two compartment configurations.NORWESCO septic tanks are for BELOW GROUND USE ONLY. Using the tanks above ground may result in deformation of the tank. It is far more cost-effective to utilize one of NORWESCO’s above ground tanks that are specifically designed for above ground use and applications.The tanks described and shown on this page cannot be used as pump tanks and must be kept full at all times.PRE-PLUMBING: All of our NORWESCO septic tanks that are 750 working gallons andabove are “pre-plumbed” with PVC inlet and outlet assemblies. Assemblies andtheir components are made of either SDR35 or SCH40 PVC depending on state orlocal code requirements. All assemblies are sized according to code requirementsas well. Finally, an EPDM gasket is placed between the “T” assembly and thetank wall to assure watertightness. NORWESCO septic tanks will arrive to youready for installation.WATERTIGHT DOMED LIDS: All septic tanks manufactured at all facilities, are equipped with a watertight domed lid. This domed lid is significantly stronger than previous lids we have offered. When leaving our factory, the lid(s) will be attached to the tank with stainless steel screws and come standard with a foamed, polyethylene gasket between the lid and the tank. This gasket provides a watertight seal at the lid area.MANHOLE EXTENSIONS AND LID/RISER COMBINATIONS: Again, at all facilities, the notches in the manhole area(s) of the tank have been removed as the “interruption” in the manhole, or circle, weakens that area. The lugs on the accessories have also been removed. See tank accessories for more information on the accessory items.NORWESCO septic tanks are backed by a full three-year warranty and have been certified by state and local health departments from coast to coast. Where applicable, NORWESCO septic tanks have been certified by both IAPMO and CSA.Across the United States and Canada, there are certain health code requirements that our tanks must meet. These codes are regulated by the state, county or province.Click here for Septic Tanks in HawaiiTank Depot Tanks Light Weight – Durable – Easy to Install

Norwesco 1000 Gallon Plastic Septic Tank For Sale

  • Pre-plumbed with PVC tees and septic adapters already fitted

Important Note: Tank must be left 1/4 full at all times including installation.

Disclaimer: This tank is intended for usage below ground only.

State RequirementsApprovals

Our tanks must comply with a variety of health code standards that are in place across the United States. Depending on where you live, these codes are governed by your state or county. Please speak with your local health agency if you need assistance determining which tank you will require.

Septic Tank Standards:

  • Molded in a rotational motion. one-piece. seamless. tank that is completely watertight
  • Polyethylene is unaffected by the compounds found in soil. gaseous sewage
  • Tanks made of polyethylene will not rust or corrode. Strict quality standards guarantee that the septic tank is safe for the environment. Connections to the plumbing system according to Schedule 40
  • Standard plumbing is something that all area installers or professionals are familiar with. Extensions for the risers are not included. Excellent shipping item that is virtually unbreakable.

Frequently Asked Septic Tank Questions

Sculpted in a rotational fashion one-piece. seamless. container with a tight seal In contrast to soil chemicals, polyethylene is not harmed by them. gaseous sewage Tanks made of polyethylene will not rust or corrode; they are also lightweight. Environmentally friendly septic tanks are ensured by strict quality criteria. Plumbing connections according to Schedule 40; Standard plumbing is something that all local installers and professionals are familiar with. It is not including any riser extensions.

  • In most cases, it is not authorized to place the plastic septic tank beneath a driveway, and doing so will invalidate the guarantee. Keep tanks out of the line of heavy and vehicle traffic regions, and don’t put them beneath driveways.

A driveway is not authorized to be used as a foundation for a plastic septic tank; doing so will invalidate the guarantee. Keep tanks out of the line of heavy and vehicle traffic regions, and don’t put them under driveways.

  • Yes. the combination of sand and gravel A mixture commonly referred to as “pea gravel” is recommended. (Please refer to the installation instructions above.)

How about using a septic tank that is above ground?

  • Underground plastic septic tanks are intended for use solely below ground. They are not intended for above ground usage. The use of above-ground storage tanks may result in the tank’s distortion and degradation. When compared to underground storage tanks, it is significantly more cost-effective to employ an above-ground storage tank that has been particularly constructed for above-ground uses.

4. Is it possible to keep hot water in plastic septic tanks?

  • Do not expose the tank to water temperatures more than 100 degrees Fahrenheit. The maximum storage temperature for polyethylene storage tanks is 120 degrees Fahrenheit. Contents that have been exposed to temperatures in excess of 120 degrees Fahrenheit, even for a brief period of time. can cause structural integrity of the tank to be compromised, making it more prone to deformation and collapse

5. What is the best method of accessing subterranean plastic septic tanks?

  • Each plastic septic tank is provided with manhole access gates for easy maintenance (1 or 2 depending on tank). Additionally, risers can be placed to the top of the tank to provide for access from the ground level. A riser would save you from having to dig up the dirt above the manway in order to get access
  • Otherwise,

6. Is it possible to pick up a plastic septic tank in the area?

  • In many instances, the answer is yes. You must place an order in advance in order to pick up a plastic septic tank and save on shipping costs. When you receive notification that your tank is available for pickup. Plastic-mart will offer you with a six-digit trip number that will allow you to visit them and pick up your tank Monday through Friday from 8:30 a.m. to 2:00 p.m. Plastic-mart and the local manufacturers are grateful for the opportunity to provide local pick-up as well as the cooperation required to ensure that the process is as efficient as possible.

What size of septic tank do I need?

Probably one of the last things on your mind when you are constructing a new house is the location of your septic system. After all, shopping for tanks isn’t nearly as entertaining as shopping for cabinetry, appliances, and floor coverings. Although you would never brag about it, your guests will be aware if you do not have the proper septic tank placed in your home or business.

septic tanks for new home construction

The exact size of the septic tank is determined mostly by the square footage of the house and the number of people who will be living in it. The majority of home septic tanks have capacities ranging from 750 to 1,250 gallons. A 1000 gallon tank will most likely be required for a typical 3-bedroom home that is smaller than 2500 square feet in size. Of course, all of this is dependent on the number of people who live in the house as well as the amount of water and waste that will be disposed of through the plumbing system.

For the most accurate assessment of your septic tank needs, you should speak with an experienced and trustworthy sewer business representative. They can assist you in planning the intricacies of your septic system, including which sort of septic system will be most beneficial to you.

planning your drainfield

Here are some helpful hints for deciding where to locate your drainfield when you’re designing it.

  • Vehicles should not be allowed on or around the drainfield. Planting trees or anything else with deep roots along the bed of the drain field is not recommended. The roots jam the pipes on a regular basis. Downspouts and sump pumps should not be discharged into the septic system. Do not tamper with or change natural drainage features without first researching and evaluating the consequences of your actions on the drainage field. Do not construct extensions on top of the drain field or cover it with concrete, asphalt, or other materials. Create easy access to your septic tank cover by placing it near the entrance. Easy maintenance and inspection are made possible as a result. To aid with evaporation and erosion prevention, plant grass in the area.

a home addition may mean a new septic tank

Do not make any big additions or renovations to your house or company until you have had the size of your septic system assessed. If you want to build a house addition that is more than 10% of your total floor space, increases the number of rooms, or necessitates the installation of new plumbing, you will almost certainly need to expand your septic tank.

  • For a home addition that will result in increased use of your septic system, your local health department will require a letter from you that has been signed and authorized by a representative of your local health department confirming that your new septic system is capable of accommodating the increase in wastewater. It is not recommended that you replace your septic system without the assistance of a certified and competent contractor.

how to maintain your new septic system

Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company devoted to delivering outstanding septic tank cleaning and septic tank pumping services to households and business owners throughout the Michiana area. “We take great delight in finishing the task that others have left unfinished.” “They pump, we clean!” says our company’s motto. Septic systems are something we are familiar with from our 40 years of expertise, and we propose the following:

  • Septic tank cleaning and septic tank pumping services are provided by Norway Septic Inc., a service-oriented company dedicated to providing excellent septic tank cleaning and septic tank pumping services to residents and business owners throughout the Michiana area. When others fail to complete a task, we take great delight in completing it. “They pump, we clean!” is our company motto. Given our extensive septic system knowledge and over 40 years of experience, we suggest the following:

common septic questions

Here are some of the most frequently asked questions by our septic customers.

How do I determine the size of my septic tank?

If you have a rectangular tank, multiply the inner height by the length to get the overall height of the tank. In order to find out how many gallons your septic tank contains, divide the number by.1337.1337

How many bedrooms does a 500-gallon septic tank support?

The exact size of the septic tank is determined mostly by the square footage of the house and the number of people who will be living in it. The majority of home septic tanks have capacities ranging from 750 to 1,250 gallons. A 1000 gallon tank will most likely be required for a typical 3-bedroom home that is smaller than 2500 square feet in size.

How deep in the ground is a septic tank?

This is mostly determined by the square footage of the house and the number of people that will be living in it, as well as other factors. A typical household septic tank holds between 750 and 1,250 gallons of water. Typically, a 1000 gallon tank will be required for a three-bedroom home that is less than 2500 square feet in size.

Underground

Drainage Systems (Septic Tanks) (larger sizes available by special order) 300-gallon drum (pump-tank) 500-gallon drum (pump- tank) 32″ W x 6’8″ L5’8″ W x 4’3″ L 5’9″ Tall5’9″ Tall32″ W x 6’8″ L5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall5’8″ Tall Inlet: 59″Outlet: 56″Inlet: 49″Outlet: 46″Inlet: 59″Outlet: 56″ Tank with a capacity of 1000 gallons 750-gallon drum (pump- tank) 5’8″ W x 8’8″ L6’8″ W x 5’7″ L5’7″ Tall, 9,750 lbs.5’4″ Tall, 9,750 lbs.5’4″ Tall, 9,750 lbs.

Flow rate at inlet 49″ flow rate at outlet 46″ Outlet: 50″ x 53″ x 53″ x 50″ Tank Capacity: 1250 gallons Tank Capacity: 1250 gallons 6’8″ W x 9’4″ L6’8″ W x 7’5″ L 5’4″ Tall, 12,000 lbs.5’9″ Tall, 11,000 lbs.6’8″ W x 7’5″ L 6’8″ W x 7’5″ L 6’8″ W x 7’5″ L 6’8″ W x 7’5″ L 6’8″ W x 7’5″ L Intolerances: 53″ and 50″ 57.5″ incoming; 54″ incoming; Tank with a capacity of 1750 gallons and three compartments 1000-500-250 gal., 6’8″ W x 12’10” L, 5’4″ tall, 15,600 lbs.

  • (the third component is a pump) the chamber) (inlet: 53″outlet: 50″chamber) 1500-gallon tank with three compartments 12,000 lbs.(3rd component is a pump) 5’8″ W x 12’6″ L825-425-250 gal.
  • 52″ inlet x 48″ outlet x 52″ chamber) Tank with a capacity of 2000 gallons and three compartments 6’8″ W x 11’5″ L, 1250 gallons, 750 gallons, 250 gallons, 5’9″ tall, 15,000 lbs.
  • chamber) (inlet: 59″outlet: 56″chamber) Tank Capacity: 2250 gallons Tank Capacity: 2500 gallons 6’8″ W x 13’6″ L6’8″ W x 13’6″ L5’9″ Tall, 16,500 lbs.
  • 5’10” tall and weighing 17,500 lbs.
  • Adventex Treatment Systems are manufactured by Orenco.
  • Ecoflo Coco Filter System from Premier Tech (Manhole Risers are made by EZ-Rise.
  • 30″ diameter with a height of 12″ Tuftite is available in two sizes: 20″ and 24″ in diameter and 6″ and 12″ in height.

Plus, polylok comes in two sizes: 20 and 24 inches in diameter and 6 and 12 inches in height. Concrete dimensions: 23.75″ ID x 28.5″ OD in three different heights: 8, 10, and 12 inches

1000 Gallon Septic Tank – Single Compartment. 60”D x 51”H x 127”L

  • Household wastewater treatment, on-site sewage treatment, residential applications, light commercial hotels, schools, and neighborhood applications, and more are available.

Notes

  • All images and drawings are for illustrative purposes only and may not always depict the exact product being advertised. It is possible for dimensions on polyethylene tanks to differ by +/-3 percent (typical rotational molding tolerance). It is recommended that venting equipment be sized to allow for a maximum pressure or vacuum of 1/2″ water column (0.018 PSI) in polyethylene water tanks when used for water storage only at atmospheric pressure. The tank is made of BPA-free and FDA-approved materials. The resin is produced in NSF-certified manufacturing facilities. The tank must be installed and used in accordance with the manufacturer’s instructions for usage and installation in order for the warranty to be valid. According to the tank manufacturer’s recommendations, flexible connectors must be used on all fitting connections.
  • BPA-free and FDA-compliant
  • High-quality and long-lasting construction
  • 3-Year Manufacturer’s Warranty
  • Currently in stock and available for purchase

$1,590.00 in U.S. dollars Prices on all items displayed on our website are subject to change as a result of resin price changes that are beyond our control. Please contact our office to obtain verified price or to be placed on our waitlist for future availability (866-969-9404). Shipping and Handling Information

Ships From CA, NE, AR, WV, GA
Shipping Cost Call 866-959-7593 for Shipping Quote

Description

$1,590.00 is the amount of money. The price of all goods displayed on our website is subject to change due to resin price hikes beyond our control. You can acquire pricing confirmation or be placed on our waitlist by contacting our office (866-969-9404). Detailed Information About Shipping

Capacity 1000
Length 127″
Width 60″
Height 51″
Material High Density Polyethylene (HDPE)
Weight 250
Inlet 3″ Pre Drilled hole with Septic T and Gasket
Outlet 3″ Pre Drilled hole with Septic T and Gasket
Lid Size/type (X2) 20″ NexGen D2 Lid and Gasket
Specific Gravity 1.0 (Septic use only)
Manufacture Snyder

Additional Information

A 1000-gallon two-compartment yellow septic tank from Norwesco, the 41721 is built to last and is simple to install, making it a popular choice. Featuring a corrugated ribbed construction for improved structural stability and a three-year guarantee from the date of production, this two-compartment septic tank comes with a three-year warranty from the date of manufacture. The Norwesco 41721 is created by the use of the rotational molding technique. As a result of this technique, a one-piece watertight tank is produced, with no seams to seal or worry about.

The Norwesco 41721 is a 1000-gallon two-compartment yellow septic tank that incorporates a waterproof cover that is stronger than other lid designs as well as a gasket between the tank and the lid to ensure a watertight seal between the two compartments.

** Because of the substantial weight and size of this goods, as well as the variable nature of shipping rates, the online delivery cost calculations may be overstated in certain cases.

AK Industries – Septic Tanks – 1,000 Gallon Poly Septic Tanks

  • The Norwesco 41721 is a 1000-gallon, two-compartment yellow septic tank that is built to last and is quick and simple to set up. This 2-compartment septic tank, which comes with a three-year warranty from the date of construction, is built with a corrugated ribbed design for improved structural strength and comes with a three-year warranty. In order to make the Norwesco 41721, the rotational molding method is utilized. As a result of this technique, a one-piece watertight tank is produced, with no seams to seal or worry about. Additionally, because it is constructed of Heavy Duty Polyethylene (HDPE), it is unaffected by sewage on the inside or soil chemicals on the outside. In addition to a waterproof lid that is stronger than other lid designs, the Norwesco 41721 1000 Gallon Two-Compartment Yellow Septic Tank incorporates a gasket between the tank and the lid to ensure a watertight seal there as well. Manhole extensions and lid riser combinations are offered to suit specific code criteria and/or to bring tank access up to grade. ** It is possible that the online shipping cost calculations for this goods will be overstated due to the considerable weight and size of this device, as well as variable shipping rates. If you have any questions about the shipping prices, we recommend that you contact our customer service team before making a purchase.

Complete Septic System Brochure and Installation Manual AK Industries, Inc. is the manufacturer. Deliveries are made within 1 – 4 weeks of receiving the order.

Please use the “Request a Quote” form

  • Resistant to sulfuric acid deterioration, which tears down concrete
  • Engineered ribbed design
  • Polyethylene of superior grade
  • Internal skeletal support was not required in the design of this product. One-piece design with a lot of character

Efficiency

  • Plastic is lightweight, making it simple to install and move
  • Bottom that is flat and even
  • Suitable for locations with a high water table
  • Even for those who require a deep burial depth, this product is ideal.
  • Only plastic septic tanks are available on the market, and they come with a limited life-time warranty. Customer Service that is dependable
  • Excellent and consistent lead times
  • This product has been approved for usage in nearly every state.

Welcome to the world of septic tanks!

At AK Industries, we strive to be recognized by our customers as industry leaders in the manufacture of high-quality injection-molded products. We strive to do this by adhering to a corporate philosophy that is based on honest customer service, great design, and a dedication to constant progress and innovation.

Leave a Comment

Your email address will not be published. Required fields are marked *