Four-inch pipe is standard, and it should extend far enough under the house to connect with the main soil stack, which is a 3-inch pipe that extends vertically past the main bathroom and through the roof.
- Sewer drains from laundry sinks or washing machines are 2 inches in diameter and those from sinks in the kitchen, bathroom or powder room generally use a 1.5-inch pipe. The main sewer pipe leading to the septic tank or public sewer is usually 4 inches. It is important to look to the local plumbing code to see if it varies from these standards.
Should I use 3 or 4-inch drain pipe?
Waste drain pipes for toilets in modern plumbing systems are either 3 inches or 4 inches in diameter. The wider the pipe, the more waste it can move and the less likely it will be to clog. A 4-inch pipe can carry about twice the waste of a 3-inch pipe.
What kind of pipe do you use from house to septic tank?
Laying Out a Septic-Tank Disposal System. The septic tank should be positioned at least 50 feet from the house proper. ABS or PVC plastic or cast iron pipe can be used to connect the tank to the house drainage system.
How big is a septic drain pipe?
Typically septic trenches are 8 to 12 inches wide in some applications, or 18″ to a maximum of 36″ wide in traditional, conventional septic drainfield designs.
Is 3-inch sewer pipe big enough?
3-inch drain pipes are better at managing single toilets. But if there are multiple toilets on a 3-inch drain, it is more likely to clog. On the other hand, a 4-inch drain can handle the waste from multiple toilets.
How many toilets can be on a 4-inch drain?
4″ waste line can support 90 DFU’s, Toilets can be 3–4 DFU’s depending on how many gallons per flush. So, 22 toilets if they use a lot of water. 30 if they’re the low flow type.
Can a toilet and shower share the same drain?
In the US, with modern regulations, in most municipalities, yes, they do. The water and solids from your toilet waste line and the water from your drains end up in the same sewer line, if you have access to a municipal sewer system.
What size is main drain line?
Sewer drains from laundry sinks or washing machines are 2 inches in diameter and those from sinks in the kitchen, bathroom or powder room generally use a 1.5-inch pipe. The main sewer pipe leading to the septic tank or public sewer is usually 4 inches.
Why the inlet pipe in the septic tank is higher than the outlet pipe?
Level the septic tank: The septic tank inlet tee is designed to be higher than the septic tank outlet tee. This helps assure that incoming sewage clears the baffle and enters the tank correctly, while outgoing effluent does not carry along floating solids, scum, or grease (which would clog the drainfield).
What is the fall on a 4-inch sewer pipe?
For 4-inch PVC piping and a building sewer less than 50 feet long, the minimum slope is 1 inch in 8 feet, or 1/8-inch per foot, and the maximum is 1/4-inch per foot. For sewers longer than 50 feet, the slope should be 1/4-inch per foot.
What size is a toilet drain pipe?
The standard size of a toilet drain pipe is 3 inches in diameter, but the drain can be up to 4 inches in diameter. The drain pipe is usually connected to a 3-inch schedule 40 toilet drain pipe.
Can a toilet drain into a 2 inch pipe?
Unless two toilets are on the same drain and then it must be a 4-inch plumbing waste pipe, the toilet requires a drain pipe of 3 inches in diameter. Unless there is a toilet discharging into the piping, systems with less than nine units can use a 2-inch pipe.
Can a toilet drain be 3 inches?
Regardless of your plumbing code, the minimum drain size for a toilet is 3 inches. Water closet’s flushing 1.6 gallons (or less) are rated at 3 DFUs (drainage fixture units). Some older model toilets, flushing over 1.6 gallons per flush, are rated at 4 DFUs. The IPC allows 42 DFUs on a 3 inch building drain.
How many toilets can you have on a 3 inch line?
As a horizontal branch 3″ is good for 20 DFU’s or 4 bathroom groups.
Size of pipe to the Septic Tank?
Notifications about Septic Tanks Consult with your neighbors to see whether they have similar lots and pitch hills as you have. as well as the sewage pumping firm Then there’s the local plumbing permit office and the health department to consider. Plan ahead of time for a future municipal hookup by installing piping. When it comes to plumbing, it is always preferable to plan ahead of time. fundamentals at: formatting a hyperlink Scott Townsend penned the following: Both the house and the system are brand new.
A new 2nd dwelling, new wires, a new tank, and so forth It will be drained into the new tank, which will then be pumped up to the field.
According to what I’ve heard, the 4″ provides greater flow, is simpler to clean, and so on, but the 3″ causes your liquid level to be higher, allowing the particles to be carried away.
Thanks “Scott Townsend” was the name of the person who wrote the note.
formatting a hyperlink Formatting linkFor all septic tanks, the inlet and outlet pipes should be at least 4-inch diameter Schedule 40 PVC, cast-iron, or other approved pipe, and they should be protected by baffles or sanitary ties made of acid-resistant concrete, acid-resistant fiberglass, or acid-resistant plastic.
- Sewers must have a minimum diameter of 4 inches and be installed with tracer tape or toning wire.
- Minimalvelocities are acceptable in some situations.
- Inverted siphons must be built to flow at a velocity of 0.5 feet per second or more, based on a Hazen-Williams coefficient of 100, and must have a minimum diameter of 4″ or greater.
- Is there a link to Scottformatting?
- As long as you keep the size of your turds to a minimum when you take a dump, 3 inches is OK.
- Make certain to use high-test nylon fishing line for the stitches so that they will last for years.
Site Timeline
- It’s possible that garages will need to be rearranged in order to accommodate this device. It has an IC
- It was last updated in
- It has an IC.
Home Repair
Drainage is one of those things that you may overthink to the point of being ridiculous. In order to tell me what I already know, I’ve hired an engineer who charges me $150 an hour, but I need his stamp on some paper to prove that it has been engineered. In the meantime, he’s wasting his time and mine by attempting to calculate the amount of flow versus distance, as well as the resistance of the inside walls of various-sized pipes in relation to the angle of the slope. The fact that we’re going to install it the way we want it anyhow is enough to make me delirious, but his official stamp needs to be on it anyway.
- You don’t have to be concerned with the size of the pipe for the solids as much as you do with the slope.
- Nothing is moving because the water is too shallow.
- I like to work with a 5 percent margin of error since the arithmetic is simpler for me and my margin of error is equal on both sides.
- I start with three-inch lines for my toilets and then increase them to four-inch lines after everything is in place.
- Incorporate as many clean-outs as possible into your plan.
- Depending on the vents just makes things more difficult when you may install them for very little money throughout the construction process.
In addition, I installed a cleanout on the line that runs from the home to the tank and/or where there is a bend in the line. As my drain exits my house on its route to the tank, it has a long sweeping 90 degree bend in the pipe. I marked the spot with a “T” and a clean-out. Eddie
How to Run a Septic Tank Line From Your House
A septic system is made up of two lengths of pipe that are connected together. Initially, it runs from the house, where the system services are located, to a tank, where the waste is separated and solids settle out. The second section runs from the tank to the drainage field, where fluids from the tank are dispersed into the earth underneath the tank. The process of installing the first run of pipe is quite similar to that of installing a traditional sewage line. It is necessary to maintain a downhill slope to the storage tank.
Locating the Septic Tank
The tank serves as the nerve center of the septic system. It is required to be situated between the residence and the drainage field. Each and every septic installation must begin with a soil test, and depending on the results, soil conditions may necessitate the placement of the tank in a less-than-ideal site for digging sewer lines. Also required are minimum setback distances from property borders, functioning wells, surface water and other obstructions to provide a safe working environment.
Tank Depth
A standard septic tank has a 4-inch intake at the top, which is positioned towards the bottom. Ideally, a 1/4-inch-per-foot slope toward the pipe from the house should be maintained by the pipe connecting to it. To put it another way, for every 10 feet of distance between a tank and a home, the inlet must be 2 1/2 inches lower than where the pipe departs the house at its lowest point. The pipe usually exits at ground level, although it may need to pass beneath a foundation footing or concrete pad in rare cases.
Digging the Trench
The trench for the septic pipe should be dug before the hole for the tank since you will need a backhoe to complete the work and the tank will get in your way if it is already in the ground. To allow rainfall to drain properly, the pipe should be placed on a 2- or 3-inch bed of drain rock, so remember to account for this extra depth when digging. It is normal to use a four-inch pipe, and it should be installed far enough down to link with the main soil stack, which is a three-inch pipe that runs vertically past the main bathroom and through the roof of the home.
Precautions
Local building and health agencies will demand permits for a septic tank installation. You will also be required to submit a design plan before the permits will be provided, so prepare ahead of time. This layout should be developed in collaboration with a local builder who is familiar with the unique characteristics of the topography in your neighborhood. Stay away from planting trees or plants near the tank, drainage field, or any of the pipe systems.
They will be drawn to the pipes in their hunt for nutrition, and their roots will be able to successfully block them. You will be unable to use your septic system until the roots have been removed from the pipe. Removal may be both expensive and time-consuming.
What Type of PVC pipe is required for a septic tank inlet?
The question has been seen 47k times. The sort of PVC pipe that should be used for the main septic drain line from the home to the septic tank is something I’m attempting to figure out. According to the IRC:
Chapter 5 – Materials
505.1 Pipe is a pipe that is 505.1 in diameter. Unless otherwise specified, pipe for private sewage disposal systems must have a smooth wall and meet one of the standards listed in Table 505.1. SCH 40 PVC appears to be acceptable, but what about thin wall sewer/drain pipe material is acceptable? In particular, I’d like to know whether the pipe wall must be especially thick, or whether this is merely a decision dependent on the placement of the pipe (for example, traffic areas versus no traffic, tree roots, etc).
- This is a Sch 40 pipe with a thick wall.
- Is this inclusive of the thin-wall sewer pipe mentioned above?
- asked At 20:19 on May 21, 2014, Ryan Griggs is a professional basketball player.
- The pipe is not the place to save a few dollars; you may live to regret (and smell) your decision later down the road.
- The same is true for pipes.
- Rather of a cast-in-place baffle, a PVC Tee inlet baffle should be used instead, and it should be 6x4X6 with a suitable 6″ pipe extension for the bottom leg.
- A large portion of the remaining pipe is only allowed for use on the drain-field side of the system, which is responsible for distributing the treated wastewater.
answered May 23rd, 2014 at 1:39 p.m.
It is beyond me to understand why one pipe is preferred over another, but in all of my years as a project manager, Sch 40 pipe has been the sole pipe utilized, with no other type of PVC pipe being used.
I simply brought it up since it is the only other acceptable source of information.
JackJack30.4k1 gold badge19 silver badges50 bronze badges2 JackJack30.4k1 bronze badge Schedule 40 is strictly adhered to.
As a result of its tapering concave aperture, which starts at 6″ and shrinks to 4″ (?) at its narrowest point.
Also, in agreement that this is not a place to save money, are you advocating a 4″ T connection for subsequent practical needs, or are you advising something else? answered @ 0:04 on March 29, 2015
Not the answer you’re looking for? Browse other questions taggedpipesewersepticorask your own question.
The appropriate size of PVC pipe for a sewage drain is determined by a number of criteria. No matter what material is used in its construction, a sewer drain is unquestionably an item that you want to function properly at all times. The size of sewage drains does not always equate to the quality of the drains. The correct pipe sizing ensures that sewer waste is transported away from the house as quickly as possible.
Size
Standard practice dictates that sewage lines heading away from a toilet have a diameter of 3 inches. Sewer drains from laundry sinks or washing machines are typically 2 inches in diameter, whereas those from sinks in the kitchen, bathroom, or powder room are often 1.5 inches in diameter. The main sewage pipe that connects the house to the septic tank or public sewer is typically 4 inches in diameter. It is critical to check the local plumbing code to determine whether it differs from these minimum requirements.
Misconceptions
Some individuals believe that by installing bigger pipes, they may reduce the probability of clogging. This may out to be a mistake. Solid wastes are helped to travel through the pipe by the water pressure, and wide pipes assist to disperse that pressure. As a result, a longer pipe may cause the flow of drain water to slow down, resulting in waste accumulating.
Expert Insight
Tim Carter of Ask the Builder advises a 2-inch sewer drain on a bathtub, which is the same size as the drain required by most plumbing rules for a shower. Although you may be able to get away with a 1.5-inch drain, a 2-inch pipe allows for more room for a plumber’s snake and prevents hair from clogging the drain.
How Much Slope for Septic Line?
This page contains information on sitework, including how much slop for a septic line to have. Peter inquires: My builder has recently completed the installation of our septic system, and I’m afraid that he did something incorrectly. The drain field looks to be at a greater height than the tank’s exit, which is consistent with this. My brain doesn’t comprehend how the tank may empty upwards. Is there something I’m overlooking? Answer: Except if you have a mound system, or another pumping system with a dosing chamber and lift pump, you are accurate in assuming that you will require a downhill slope in your sewage pipes, which is not the case.
- The leach lines themselves, on the other hand, should be leveled out.
- Sewage lines should be sloped downhill to the septic tank and drain field at a rate of at least 1/4 inch per foot of length.
- To avoid clogging, steer clear of sags and sudden curves.
- The fear is that the water would flow too quickly and leave sediments behind, causing the pipe to clog.
- In situations when it is important to carry wastewater uphill, there are several different pumping system types that may be employed.
- I would consider getting in touch with the person who created your system to discuss the problem and, if feasible, have them come out and assess the location.
- It’s ideal if you can put your complaints in writing and send them to the contractor.
- An upward line such as the one you describe will never function effectively.
- Also read this article.
When Is the Best Time to Take a Perc Test? How much does a perc test cost? Who Should Be Hired for the Perc Test? After a failed perc test, should you retest? Should I use a Sand Filter with my existing septic system? Examining the condition of the wellSEPTIC SYSTEMView all articles Q and A Index
Reader Interactions
How far do you have to run to reach the finish line? If you’re 100 feet distant, your septicinlet should be between 3 and 7 feet deep, with the first five feet providing a beautiful 5 percent gradient for drainage. When it comes to distance, the rule of thumb is to place cleanouts at a distance that is somewhat less than double the distance you can reach with a snake. From the House, a Diatance The requirements will differ from one location to another, but the standard minimum distance from the home is 10 feet.
- Furthermore, what size pipe is used to connect to the septic tank?
- Slope the pipe at a rate of 1/4 inch per foot (at a minimum, 1/8 inch per foot) toward the tank.
- A standard septic tank has a 4-inch intake at the top, which is positioned towards the bottom.
- To put it another way, for every 10 feet of distance between a tank and a building, the intake must be 2 1/2 inches lower than where the pipe exits the building.
- In most cases, it is not a good idea to construct a deck near or on top of an aseptic tank.
- Frost footings and imposing deckloads over a septic tank have the potential to cause damage to the tank and waste pipes.
How to Connect Pipes to a Septic Tank
Septic tanks are connected to dwellings by four-inch pipes. Image courtesy of dit26978/iStock/Getty Images. Most contemporary septic tanks, whether constructed of concrete or plastic, are divided into two compartments by an internal baffle and equipped with an intake and output port. In most cases, when you first install the tank, each port has a preinstalled 4-inch sanitary tee fitting. You connect the waste line from the building to the inlet fitting and the drain line to the outlet fitting either by gluing it or by using a mechanical flexible coupling to connect the two lines (often referred to as aFernco coupling).
Septic tanks used to have only one chamber in the olden days.
The scum layer contains greases, oils, and other lighter-than-water contaminants that could clog the soil.
Whatever your feelings about the necessity of the tees, they serve as an insurance policy against the failure of the septic tank baffles, and it is smart to have them installed.
In order to keep debris out of the pipes, some plumbers put grates on the top portions of tees. However, these grates are not required, and under no circumstances should grates be installed on the lower portions of tees, since this will cause the pipes to clog.
How to Install Septic Tees
The installation of the tees on the septic tank must be done from the inside of the tank if the tees do not come with the tank. A 4-inch tee is normally firmly secured by predrilled or, in the case of concrete tanks, preformed holes in the tank’s inlet and outflow holes. A bead of butyl or silicone caulk around the perimeter of the tee on both sides of the tank will enough in most cases, but it’s not a terrible idea to apply some in case you do need glue. The top of the tee should have a short piece of tubing attached to it to allow the aperture to extend over the scum layer in the tank, while the bottom of the tee must extend below the scum layer, or around 2 feet below the tee, to allow for proper drainage.
Connecting Inlet and Outlet Pipes
The installation of the tees on the septic tank must be done from the inside of the tank if the tees do not come pre-installed. The inlet and outlet holes are predrilled or, in the case of concrete tanks, preformed, and they are typically sized to accommodate a 4-inch tee snugly in the tank. You don’t always need glue, but it’s never a bad idea to have some on hand. A bead of butyl or silicone caulk around the circumference of the tee on both sides of the tank can do the trick. Ideally, a short piece of tubing should be linked to the top of the tee, allowing it to extend beyond the scum layer in the tank; however, the bottom of the tee should extend below the scum layer, or around 2 feet below the tee.
Finding the right size PVC pipe for each job
Q: Hello, Tim. I went to get some plastic drain pipe, and after looking at all of the different sorts, my head started to throb from the strain. I made the decision to leave the store and conduct some further investigation. I’m working on a number of projects that will necessitate the use of plastic pipe. I need to add a bathroom to a room addition, and I also need to replace old, cracked clay downspout drain lines. I also want to install one of the linear french drains that I saw on your website to help dry out my basement, which I found on your website as well.
- — Lori M., of Richmond, Virginia.
- I recently completed the installation of a fairly unique plastic pipe to vent the new high-efficiency boiler that my daughter purchased.
- It’s critical to understand that there are many different types of plastic pipes that can be used, and that the chemistry of each one is quite complex to begin with.
- When it comes to drainage pipes, PVC and ABS plastic pipes are perhaps the most prevalent types you’ll come across on the job.
- PVC is a terrific material that I’ve worked with for decades.
- The most common sizes you’d find in your home are 112-, 2wo-, three-, and four-inch diameters, to name a few.
- Shower stalls and washing machines frequently use two-inch pipes to drain, and it can also be used as a vertical stack to drain kitchen sinks.
The four-inch pipe is utilized as the building drain, which is installed beneath floors or in crawlspaces to convey all of the wastewater from a residence to a septic tank or sewage system.
Pipe-sizing tables are used by plumbers and inspectors to determine what size pipe should be used in which location.
A number of years ago, the only PVC pipe I would use for house plumbing was schedule 40 PVC tubing.
It’s referred to as cellular PVC.
Make certain that this is clear with your local plumbing inspector first.
A sturdy pipe with thinner sidewalls than schedule 40 pipe, it is used for a variety of applications.
More than 120 feet of six-inch SDR-35 pipe connected my house to the city sewer system in the last house I built for my family, which was my first.
Make certain that the two rows of holes are pointing downward.
Q: Hello, Tim.
When I walked into the room the other day to check on something, there was a puddle on the floor to my surprise.
Unfortunately, there was no damage to the vehicle.
I’m baffled as to how it may be seeping elsewhere.
If you don’t want to cause a wider leak, just be honest with me about it.
— Brad G.
On all of the projects I worked on, I did practically all of the plumbing myself.
Movement is present in ball valves, as well as other types of valves.
Over the years, a variety of materials have been crammed into this extremely small space in order to prevent water from leaking out.
To remove the ball valve handle from the valve shaft, simply unscrew the hex nut that holds it in place on the shaft.
This is the packing nut, as the name implies.
While facing it, just a very modest degree of clockwise rotation should be applied.
Packing nuts should not be overtightened.
This will help to prevent a catastrophic flood. Understand how it operates and keep a wrench on hand in case you need to shut it off in a hurry. A taskthebuilder.com is where you can sign up for Tim’s free email and listen to his latest podcasts.
EZflow® Septic System
By utilizing a geosynthetic aggregate modular design built for ease of installation, the Infiltrator EZflow septic system can be an environmentally responsible alternative to traditional stone and pipe drainfields. Because it does not contain any stone, the gravelless EZflow system is intended to improve drainfield performance by eliminating fines and reducing compaction and embedment that can occur with stone. Drain pipes are 3″ or 4″ in diameter, and they’re surrounded by aggregate and kept in place with durable, high-strength netting.
Bundle System Configurations:
Single Bundle7 is a collection of items that are not necessarily related to one another “8”, 10″, 12″, and 14″ diameters are available. Horizontal Bundle with diameters of 7″, 9″, 10″, 12″, 13″, and 14″ Vertical Bundle (ten, twelve, and fourteen inches) “a range of diameters Triangle Bundle with widths of 10, 12, 13, and 14 inches 5′ and 10′ lengths that are simple to contour
Applications:
- Use with advanced treatment systems
- Shallow applications (low-profile models)
- Trenchbed systems
- Fill-and-mound systems
- Pressure distribution systems
- And serial distribution systems. Systems that are installed at ground level
- Systems that allow for a step-down or a drop-box
- Systems that are commercial, community-based, or clustered
Benefits:
- Always free of fees and free of dirt
- Bundles are simple to assemble, reducing the need for heavy gear and personnel expenditures. leach field and septic pipe with gravel
- When using modular construction, it is possible to match trench measurements for the majority of system forms and sizes. Engineered to provide the highest possible storage and absorption efficiency
- The ability to contour around sloping terrain and around trees or other landscape features
- The system’s light weight makes it ideal for repairs and confined project locations. Hand-carried into place, minimizing the amount of time and work required
- 5′ or 10′ lengths with internal couplers that fit together easily
- Because of the removal of stone from the job site, cleaning will be less difficult. Produced with recycled materials rather than from a natural resource that has been extracted
- We provide a wide range of diameter and configuration options to fulfill the demands of any installation specialist
- Many jurisdictions have approved it because of its higher efficiency rating, which results in a smaller drainfield. Supported by the industry’s preeminent leader in onsite wastewater management
InstallationTip Videos are available for viewing after downloading the cutsheet.
FAQs:
May you tell me where I can receive help with local installation code, system designs, and technical concerns about products? Several installation choices and criteria are controlled by municipal rules that have been established by the health authority in your region. When in doubt, consult with your local health agency for specifics, and then adhere to their code recommendations as best you can. The Technical Services staff at Infiltrator Water Technologies may be reached at 1-800-718-2754, if you have any queries about design or installation that are not addressed here.
- A variety of septic leachfield and leach bed applications can benefit from the usage of EZflow.
- This comprises trenching, bed construction, and raised mound construction.
- How much of a reduction in the size of the leachfield can I expect if I install EZflow?
- The size of a wastewater treatment system is often determined by a mix of criteria, including the soil type and amount of wastewater to be treated (normally estimated using number of bedrooms).
- Check your local health codes for information on what is required in your region.
- Local regulations govern the spacing requirements for trenches, so check with your local health authority for more information.
- Infiltrator Water Technologies recommended that there be no gap between the sides of bundles when used in beds.
The majority of health rules prohibit the installation of septic leachfields beneath impervious surfaces such as roads and sidewalks.
Consult your local health department for information on the exact codes that apply in your region.
When it comes to minimum and maximum system cover, what is EZflow’s specification?
In a trench system, the maximum amount of cover allowed above EZflow is 96 inches.
Always check with your local health codes to see if there are any special requirements for coverage.
Yes. When it comes to contouring around existing impediments, EZflow has nearly limitless capabilities. In order to prevent soil from entering EZflow through the netting, what should be done? The soil is prevented from entering the bundles by a geotextile mesh that is woven into the netting.
Sewer Pipe Inspection
You have it now. Any size pipe, ranging in diameter from less than 2 inches to more than 8 feet. With the use of cutting-edge tiny video technology, we can now identify and locate all of these: Introducing The Jumbo Cam System is the most comprehensive and technologically advanced video inspection service ever put together. It is a non-invasive video diagnostic service that may be used to diagnose practically any sewage or catch basin system in the world. Jumbo Cam Mobile Video Diagnostic Center is a mobile TV studio and data center that may be used to diagnose video problems.
Additionally, the system generates digital color printouts of the system in schematic form, in addition to high-resolution video footage.
- Sewers, water mains, and storm drains for municipal and commercial use
- Commercial septic systems Condominiums, hotels, and apartment complexes under construction or undergoing redevelopment
“GraniteXP Software” is owned by Podgurski and is used to monitor video feeds from our Pipe Video Inspection Tools. This software is extremely powerful and accurate. Our Mobile Vans are equipped with this technology, which allows us to identify and correct problems much faster than our competitors. Beginning with Granite XP, a comprehensive data collection and management software by CUES that provides unmatched flexibility and customization, the Jumbo Cam System is put together. Granite XP, which was developed using current Microsoft Visual Studio technology and designed with an asset-based architecture, enables us to travel to any pipe segment or manhole and observe all inspections associated with it.
Features and Advantages of the CUES Software
- The Quick Find and Filter capabilities in Granite XP are powerful and flexible, and allow you to search the Granite XP database for desired inspection record(s) based on specific criteria – important for utilities that need to prioritize rehabilitation plans for an effective CMOM program. ESRI asset data imported from a master GIS database can be used to populate Granite XP’s asset database. Granite XP allows you to save standard and customized reports in PDF, HTML, or ASCII file format, and you can also email them from inside the program. Data may be exported in a variety of formats, including Oracle, SQL, Access, PACP, WRc Sewer.dat and Sewer1.dat, Hansen, Azteca Cityworks, WinCan, and ASCII. Searching for projects, assets, inspections, and observations has never been easier thanks to powerful keyword search and filtering tools. Pluggable architecture allows for the development of expansions without the need to re-architect or change the entire program. Make use of reversal configurations in a single inspection, such as “upstream against the flow” or “downstream with the flow,” in order to present upstream and downstream observations on the same inspection
- View live video and images at the same time, or select an observation on the pipe graph to jump directly to that specific point in an MPEG I, IIIV video
- We can supply complete reports for diagnosis and repair, as well as for reported compliance. Contact us for more information. In full color, on video (VHS or DVD), on paper, or in any of a number of other digital forms are all possibilities.
There’s nothing quite like the Jumbo Cam, a video diagnostic system that provides a close-up, full-color, live video image of any sewage, water, or storm drain pipe up to an incredible 100 inches in diameter and up to 4,000 feet in length (and is recordable on VHS or CD). Equipment referred to as “Mudmaster” The Mudmaster is a camera transporter that has been particularly developed to provide the weight, power, speed, high clearance, and all-wheel drive required for pipelines ranging in size from 24 inches to 200 inches.
Tandem wheels are also offered as an option.
It is possible to put the waterproof remote-controlled camera lift through a 19-inch-diameter manhole with the camera in its lowest position in order to prevent the operator from entering a limited location.
The operator can manage all transporter, camera, and camera lift capabilities with a single hand thanks to the device’s one-of-a-kind portable joystick stick controller.
- Traction is improved in all types of pipe, under all situations, when four or eight (tandem) wheels are used together. Weight and power have been matched to optimum efficiency and capabilities. Installation of two wheels is straightforward, and the hardware is captured. Camera lift that can be controlled from a distance
- Can check lines from 24′′ to 200′′ in diameter and up to 2500 feet in length. All-wheel drive in both forward and backward directions
- Rugged, long-lasting, and completely sealed to prevent water penetration
- 3 bulbs, 255 watt light system with variable and adjustable brightness
- Stable wheel base, steerable Mudmaster camera carrier are among the features. You may use the power forward, reverse, and freewheel reverse functions. It is compatible with all CUES cameras. One-handed use of a flight stick controller to control the transporter and camera motions
- Power control unit for the Mudmaster
- Eight (8) semi-pneumatic tires with a 10.5-inch diameter
- It has the ability to spin 360 degrees and cross pipelines with several 45- and 90-degree bends.
Traction is improved in all types of pipe, under all situations, when four or eight (tandem) wheels are used. Optimized the relationship between weight and power to increase efficiency and capabilities; Installation of twin wheels is simple, and the hardware is captured. The camera lift may be controlled remotely. Can check lines from 24 inches to 200 inches in diameter and up to 2500 feet in length. Forward and reversing drive is accomplished by turning all four wheels. It is tough, sturdy, and water-resistant, and it is completely sealed.
Steerable Mudmaster camera carrier with a stable wheel base Forward, backward, and freewheel reverse are available.
Control the transporter and camera motions with one hand using a flight stick joystick.
8 semi-pneumatic tires with a circumference of 10.5 inch; It has the ability to spin 360 degrees and cross pipelines with several 45 and 90-degree bends.
- Sewers, water mains, and storm drains for municipal and commercial use
- Commercial septic systems
- Condominiums, hotels, and apartment complexes under construction or undergoing redevelopment
Specifications for Video Systems
- Accurate footage displayed on screen
- An inclinometer displayed on screen Color camera with adjustable focus and pan and tilt capabilities for a completely directed and clear vision at all times
- Pipe diameters ranging from 6 to 60 inches are available for configuration. In forward and backward, the vehicle is completely steerable. Fully submersible up to a depth of 30 meters
- RIDGID SCOUT uses a transmitter/receiver to pinpoint its location. With two access points, the range is 1300 feet
- With one access point, the range is 650 feet. a motorized cable reel that automatically retracts and extends for simple insertion and removal
- It is possible to make it portable for facility work. For large diameter charged pipelines, a flotation raft is used.
