Septic Tank Alarm What Does It Mean? (Solution found)

A septic tank alarm system is a device designed to monitor the water elevation inside the tank, and it alerts you when the water level in the tank is much higher or lower than it should be. This raises the water level inside the pump tank until the controls cycle back and come on again.

What should I do if my septic alarm goes off?

If your alarm is going off:

Switch on the alarm box or push the red button to turn the alarm off.

Look for where the red and green lights are located.
The green light means the alarm has power.
Check your septic breaker.

If the red light does not turn off after 10 hours, give your local plumber a call!

What causes the septic alarm to go off?

Septic tanks typically come with alarms for a good reason. The septic alarms are meant to go off when the water level in your septic system’s pump tank is either too high or too low because either condition can cause damage to the system and should be prevented.

Will a flooded septic tank fix itself?

Most septic tanks are not damaged by flooding since they are below ground and completely covered. However, septic tanks and pump chambers can fill with silt and debris, and must be professionally cleaned. If the soil absorption field is clogged with silt, a new system may have to be installed.

How do you know if your septic is failing?

The first signs of a failing septic system may include slow draining toilets and sinks, gurgling noises within the plumbing, sewage odors inside, continuing drainage backups, or bacteria in the well water. The area of the strongest odor will point to the location of the failure in the septic system.

Can heavy rain cause septic problems?

It is common to have a septic back up after or even during a heavy rain. Significant rainfall can quickly flood the ground around the soil absorption area (drainfield) leaving it saturated, making it impossible for water to flow out of your septic system.

Do all septic tanks have alarms?

All septic systems that use a pump to move wastewater from a septic pump tank to a drainfield or mound have an alarm installed in the house. The alarm goes off when wastewater is not being pumped from the septic pump tank to the drainfield or mound.

How do u know when your septic tank is full?

Here are some of the most common warning signs that you have a full septic tank:

Your Drains Are Taking Forever.

Standing Water Over Your Septic Tank.
Bad Smells Coming From Your Yard.
You Hear Gurgling Water.

You Have A Sewage Backup.
How often should you empty your septic tank?

Can I take a shower if my septic tank is full?

Only the water would get out into the leach field in a proper system unless you run too much water too fast. The thing to do is to run your shower water outside into it’s own drain area, but it may not be allowed where you are. Used to be called gray water system.

How long do septic tanks last?

A septic system’s lifespan should be anywhere from 15 to 40 years. How long the system lasts depends on a number of factors, including construction material, soil acidity, water table, maintenance practices, and several others.

What do I do if My Septic Alarm is Going Off?

In the event that your septic alarm goes off, it may surely create some anxiety and uncertainty; and if you happen to be experiencing this right now, then you’ve arrived to the correct location! Don’t be concerned; it does not necessitate urgent action. Instead, take your time to go through this full essay so that you will be prepared to act now or in the future if the situation arises. What Septic Systems Are and How They Work The alarm works in conjunction with the septic system to alert you when the water level within the pump tank has increased to an unsafe level or has decreased to an unsafe level.

The timer is in charge of regulating the time intervals during which the pump is permitted to pump wastewater into the drainage system.

Thus, during periods of excessive water use, the drain field is kept from getting overflowing, which might cause damage to the drainage system.

A large amount of water is injected into the system in between pumping cycles for whatever cause, and the water has nowhere else to go but back into the system’s pump tank.

Depending on how much water was and continues to be put into the system and how the pump is set up to operate on a timer, it may take many pumping cycles until the water levels are returned to normal.

There is an excessive amount of water being put into the septic system. This is the result of excessive water use, which might be caused by multiple loads of laundry, an excessive quantity of dishwashing, or a disproportionate number of long showers.

Somehow, groundwater is making its way into the system. If there is an excessive amount of standing water surrounding the septic tanks, whether generated by rain or another source, the water may seep into the tanks and cause the internal water level to rise.

It’s possible that one of the components of the septic system is malfunctioning. If anything goes wrong with your system — including the pump and floats — the alarm and timer will go off and the septic system will stop working correctly.

The Best Thing to Do If Your Alarm Goes Off Alternatively, if you hear an alert, you should press the red button or turn on the alarm box. The alarm will be turned off as a result of this action. There should be a red light and a green light on the alarm box, which should be situated someplace on the unit. The green light indicates that the alarm is operational and should be left on at all times. It is shown by a red light if the alarm is getting a signal from the pump tank indicating that the water level is increasing above or decreasing below what is expected.

If the breaker occurs to be tripped, look around the septic tanks to see if there is any standing water.
It is possible that the red light on the alarm box will go out on its own after allowing the septic system to operate for a couple of pump cycles (which should take approximately 10-15 hours).

If the red light turns off, it signifies that the system is operating properly and that it only needs to catch up with the extra water that has overflowed into the storage tank.
To be clear, an alarm signal from the septic system does not always imply that sewage is about to back up into the house right away.
Do you require septic system repair on a regular basis or emergency service?

To arrange an appointment, please call (804) 581-0001 or send us an email through our contact page. Want to learn more about septic systems? Explore our septic system web sites by clicking on the “Septic” navigation option in the top navigation bar.

Why is My Septic Tank Alarm Going Off?

Septic tank alarm systems are a terrific method to be alerted if something is wrong with your septic tank, and they are inexpensive. When the septic alarm goes off, it means that there is a problem with the wastewater being transported to the drain field. This might be caused by a number of different factors. Most septic tanks feature an alarm that sounds when there is too much water inside of them, which might result in a backup or overflow if the problem is not addressed immediately. Once that occurrence has occurred, your float sensor will activate your alarm box, which will sound an alert depending on how high up in the tank the level has risen to be detected.

Weather issues

If it has been storming or if you have had a lot of rain in the last few days, the amount of water in your septic tank may be too much for it to handle. Standing water in the vicinity of septic systems is typically a source of problems for your septic tank. A drain field that has been saturated by rain will not enable waste water to pass through it. Overwatering your grass or draining your swimming pool in your yard might also result in a flooded area in your yard. You will need to make every effort not to use your water until the drain field is no longer inundated.

False Alarms Caused by Power Issues

Occasionally, a malfunctioning septic system alarm is caused by an electrical problem within your home or septic system. For example, your power may have flickered, resulting in a false alarm being triggered. It’s also possible that you’re experiencing electrical issues in your house, which is causing the alarm to sound.

Water Over Usage

How has your water consumption been lately? When washing double laundry, did you have a party, or did you take a long shower or bath to relax? All of this might result in more water being stored in the tank between pump cycles as a result. If it rains hard enough, the tanks may also leak, causing them to overflow and, eventually, triggering the alarm to sound.

Accidental Disconnection

The alert may ring if the pump’s power has been unintentionally unplugged by mistake. Immediately after hearing the alert go off, you should double-check that the connection is still secure and functional. Whether this is not the case, reconnect and see if the buzzer sounds again. If your septic alarm goes off again, it means that there is a problem with your pump tank someplace. Also see: How to Locate a Septic Tank.

What To Do When Your Septic Alarm Goes Off

A false alert may sound if the pump’s power has been mistakenly turned off by mistake. Immediately after hearing the alarm go off, you should double-check that the link is still intact and functional. Then reconnect and check to see whether the buzzer goes off once again. A problem with your pump tank is indicated by a recurrence of the septic alert sounding. Furthermore, see: How to Locate Septic Tank

Press the red button to activate the alarm system or the green button to turn it off
Look for the intersection of the red and green traffic lights. The green light on your alarm should always be on

The green light indicates that the alarm is operational. The presence of a red light indicates that your water level is likely excessive. Check the breaker for your septic tank. Inspect the area to make sure it has electricity and that there isn’t any standing water nearby. If the red light continues to illuminate after 10 hours, contact your local plumber for assistance. We at The Original Plumber are accessible 24 hours a day, seven days a week for emergency plumbing requirements in the Atlanta metro region.

When this occurs, we also urge that you reduce your water consumption. Normal operation of a sewer system is to pump waste water out onto a leach field, which is also known as effluent. If it is overburdened, it will require additional time to catch up.

Too much water use will prevent the septic system from having a chance to catch up. Cut back on the amount of dishwashing you do, and try to take a brief shower instead of a long one. You might be interested in learning more about:How to determine if you have a septic tank.

Maintaining your Septic Tank

Keep your septic tank in good working order, and you will reduce the likelihood of your septic tank alarm being activated. This entails inspecting the system for obstructions. If you discover a blockage, you will want to use a chemical drain opener that is safe for septic systems or a plumbing snake. To guarantee that the blockage is properly dealt with, you will want to hire a professional out to inspect and clear your drain. Over time, clogs can cause irreversible damage to your pump tank. You’ll want to be certain that you know how old your septic tank is before proceeding.

If your tank is reaching the end of its 15-year lifespan, you should consider having a new septic tank installed.
To guarantee that you do not experience any problems with your pump tank, it is recommended that you schedule an inspection once a year with a professional who is familiar with septic tank maintenance procedures.
They will also inspect the alarm to ensure that it is in correct working condition and that it is receiving the necessary power supply to operate.

As a rule, it is advised not to ignore your septic system warning because it might be an indication of a more serious problem.
Call us right away to schedule an appointment so that we can solve any pump tank difficulties you may be experiencing.

What do I do when my septic alarm goes off?

Posted on 04/37/2009 at 04:37 0 Comments on hinBlog When the water level in the pump tank rises beyond what is considered normal or falls below what is considered normal, an alarm system will sound. It is recommended that all septic systems with pumps be equipped with some type of timer. The timer regulates the amount of time that the pump is permitted to pump waste water into the drain field. During periods of increasing water consumption, this protects the drain field from becoming overloaded with water.

Systems that use timers allow the pump to run for a predetermined period of time at particular times of the day.
The water level within the pump tank will rise until the pump is able to be turned back on.
This is something that can happen from A-C.

An excessive amount of water is being pumped through the septic system.
It appears that groundwater is entering the system.
If there is an excessive amount of standing water surrounding the septic tanks, the water may seep into the tanks, causing the water level within the tanks to rise.

It’s possible that one of the components of the septic system is malfunctioning.

When the alarm goes off, pressing the red button or turning on the alarm box is the recommended course of action.

Both a red and green light will be put on the alarm box for easy identification.

The presence of a green light indicates that the alarm is operational.

After that, check the septic breaker to ensure that the septic system is receiving electricity.

If the breaker is off, turn it back on.

During this period, try to use as little water as possible to save money.

Simply put, it needed to catch up with the excess water that had been pumped into the system.

An alarm signal does not necessarily indicate that sewage is ready to overflow into the residence.

If the warning is sounding, restrict your water use to the bare minimum.

If something goes wrong, the slowed water flow will give you plenty of time to fix it before sewage backs up into the home and floods the house.

Call Us Right Now! Vac-Tec SepticWater LLC.11603 Canyon RD. EPuyallup, WA 98373PH:(253) 268-0322WS:vactecseptic.com Vac-Tec SepticWater LLC.11603 Canyon RD. EPuyallup, WA 98373 Links: Call us at (253) 268-0322 or stop by our location at to talk with an expert about your system.

Why Is My Septic Alarm Going Off?

04:37 p.m., posted in 0 Comments on hinBlog 0 When the water level in the pump tank rises over what is considered normal, or when the levels are too low, an alarm system will sound and notify you. It is recommended that all septic systems with pumps be equipped with some form of timer. Timer: This device regulates when the pump is permitted to discharge waste water into the drain field. During periods of increasing water use, this avoids the drain field from being overloaded. It is possible for a drain field to get damaged as a result of an overdose, however the timings prevent this from occurring.

The water in the system has nowhere to go but into the pump tank if there is a large amount of it put into the system between pumping cycles for whatever reason.
The fact that the pump is only permitted to operate for a limited period of time means that it may take many pumping cycles to return the water level to its normal level, depending on how much water is being brought into the system.
In this case, the septic system is being overloaded with water.

It is possible that groundwater will enter the system.
Whenever there is a buildup of standing water surrounding septic tanks, the water might seep into the tanks, causing the water level within the tanks to rise.
It is possible that anything is amiss with the pump, floats, alarm, timer, or other components, preventing them from functioning properly.

By pressing this button, the alarm will be turned off.

When it comes to traffic lights, the green light should always be on.

The red light indicates that the alarm is receiving a signal from the pump tank indicating that the water level is rising over the recommended level for the system.

Even if you haven’t seen any standing water around the septic tanks, you should still check to see if there is any.

At this time, try to save water by using it sparingly.

It only had to catch up with the additional water that had been injected into the system.

When an alarm goes off, it does not necessarily signify that sewage is ready to overflow into the house.

Reducing your water consumption to the bare minimum if the alarm is sounding A speedier response time from the pump will result as a result.

Get in Touch With Us Right Now.

ALARMS ON CONVENTIONAL SEPTIC SYSTEMS

Aeration is not present in a normal septic tank since it lacks any form of aeration equipment. If you have this sort of system and you receive an alarm, it is likely that the water level is too high. The following are the primary causes of a high water level in a traditional septic tank system:

Septic tank effluent filter that is blocked with organic matter In many typical septic tank systems, an effluent filter is installed near the tank’s outflow point. Cleaning should be performed on this filter about every 6 months. if the filter becomes clogged with particles, it will slow down the flow of water out of the system, causing the water level in the septic tank to rise
The submersible pump has failed or the float that regulates the submersible pump has failed Even though not all traditional septic tank systems will require a submersible pump, some may do so if they are properly designed. Occasionally, when gravity feeding the secondary treatment system is not possible, an electric submersible pump is employed. The failure of a submersible pump or a float switch will result in a high water level in the pump tank and the septic tank

The outlet line will be stopped, or the leach field will be flooded. An obstruction in the outlet pipe of the septic tank or a failing leach field are the other possible causes of a high water level in the tank if it does not have a submersible pump.

An often-heard myth is that a septic tank alarm signaling a high quantity of sewage signifies that the tank has to be drained out. A high level alert will not signal when a tank requires pumping, and while emptying the tank out may temporarily resolve the warning, once the tank fills back up, the alarm is likely to re-occur due to the fact that the primary problem with the system has not been rectified.

ALARMS ON AEROBIC TREATMENT SYSTEMS

An often-heard myth is that a septic tank alarm signaling a high level implies that the tank must be drained out. A high level alert will not signal when a tank requires pumping, and while emptying the tank out may temporarily resolve the warning, once the tank fills back up, the alarm is likely to re-occur due to the fact that the primary fault with the system has not been corrected.

To test if the aeration equipment is operational, check the following: If you have an air pump or compressor that is located above ground, be sure that the item is operational before proceeding. You may also check to see if the device is producing air by disconnecting the main line that connects to the aerobic tank. Alternatively, if you have an in-tank aerator, remove the cover from the aeration chamber and check to see whether the aerator is operating. If your aerator is not performing properly or is not releasing air, this is the source of your concern. Depending on the kind and condition of the aerator, it may be necessary to repair or replace the device altogether. Assuming that the aerator appears to be performing correctly, the most likely source of the warning is a high amount of water in the tank. Although this is not an emergency that must be addressed immediately, we recommend that the system be restored to operational status within 1-2 weeks of the incident. Check to check whether the water level in the aeration tank and/or the pump tank is excessively high. In a perfectly functioning system, the water level should be below the intake and at the bottom of the outflow. If the water level is high, the following are the most likely reasons why:

If you have a gravity-displacement system, a blockage in the outlet line would be the source of your excessive water level. The chlorine feeder is the most typical source of contamination. Remove the tube that contains the chlorine tablets and clean the feeder of any material that has accumulated. Also, if the system has surface discharges, make certain that the discharge exit is free of weeds and other debris. High water levels in a system with a submersible pump are usually caused by either the failure of the submersible pump or the failure of the float switch, which controls when the pump is turned on and off. The most effective method of testing a float switch is to use an ohm meter to check for continuity. The switch should be tested closed in the elevated position and open in the lowered position to ensure that it is functioning properly. By detaching the submersible pump from the float switch and running it directly from a known functional power supply, the pump may be checked. Remember that the pump will not automatically shut off when you do this, and you will need to separate it from power in order to turn it off before the tank is completely emptied.

THIS DID NOT RESOLVE MY ISSUES

If none of the troubleshooting steps listed above appear to resolve the issue you are experiencing, it is possible that there are difficulties with your control panel or alarm system that are causing the system to malfunction or causing you to get a high level alarm. In this case, we recommend that you contact a professional service provider to inspect the system and address the problem for you.

What are Septic Alarms and Do I Need One?

As a homeowner, it is critical to ensure that your septic system is in proper working order. Having difficulties with your septic system may be extremely stressful, as well as potentially disruptive to your home and way of life. A septic alarm can be of use in this situation. A septic alarm is a device that lets you monitor the health of your septic tank. The alarm will sound if the water level in the tank becomes too low or too high for a healthy tank to function properly. When your septic alarm goes off, it does not always indicate that there is an emergency situation on your hands.

It is important to know when your septic alarm goes off because it indicates that you should make repairs or other modifications to your septic system.

A expert will be able to assist you in determining exactly what is wrong with the system and how to correct it.
Their services include the repair and replacement of faulty parts, as well as advice on how to make those fixes last longer.
Septic system inspections should be performed on a regular basis in addition to the installation of an alarm system for the system.

If you do not already have a septic alarm, you may want to consider having one installed by a professional. It is an extremely useful tool for keeping track of the health of your septic system. To find out more about septic alarms and how to use them, get in touch with us right now!

What to Do When Your Septic Alarm Goes Off (With Troubleshooting Tips)

Septic systems with pumps are often equipped with some sort of warning mechanism to notify the homeowner if something is amiss. The alarm will sound if the water level in the pump tank becomes too high, or in rare cases, dangerously low. The majority of alarms will have a red light and a beeping sound. If the alarm sound is set to “quiet,” just the red light will be illuminated. When the septic alarm goes out, you should immediately turn it off. Then check to determine if the pump is receiving power from the electrical system.

The pump will complete a few of cycles and may be able to remove some of the extra water.
As a homeowner, you should be familiar with the operation of your septic system in order to identify and comprehend fundamental problems.

You’re probably thinking something along the lines of mine: Don’t I already have enough on my plate trying to figure out why my smoke detector is blaring or chirping intermittently?
We had just moved into our new home in Lewes.
So I went on the internet, chatted to a few neighbors, and ultimately obtained the services of a specialist, and the following is what I discovered.

What is a Septic Tank Alarm, and How It Works?

There are generally some warning indicators on septic systems with pumps to tell the homeowner if something is wrong with their system. Activation of the alarm is caused by an excessively high, or in certain cases, a depleted, water level in the pump tank. The majority of alarms will have a red light and a beeping sound to alert you. In quiet mode, just the red light will illuminate if the alarm sound is activated. The septic alarm should be turned off when it goes off. Then check to verify if the pump is receiving power from the electrical system if it does not.

A couple of cycles will be completed by the pump, and the surplus water may be removed.
To spot and comprehend fundamental problems, you need be familiar with the operation of your septic system.

You’re probably thinking something along the lines of mine: Don’t I already have enough on my plate trying to figure out why my smoke detector is periodically buzzing or chirping.
Considering that I had never used this sort of technology before, I was completely at a loss as to how to proceed.

After doing some research on the internet, talking to a few neighbors, and finally hiring a technician, I discovered the following: Take a moment to consider why your septic system is emitting an alarm.

Get to Know Your Septic System

It is not all septic systems that are created equal. Learn about yours, even if you’ve never had an issue with it. I didn’t have the luxury since the alarm went off just as we were getting settled in. LOL! Find the location of the alarm box. Some alarms have buttons to turn them off, while others have switches to turn them off. Open it up to see the bits that are visible. When you understand how something is intended to appear, you will be able to detect when something is not quite right. On the box, there are two lights: one that is green and one that is red.

The presence of a red light and a sound indicates that the alarm has been activated because it has received a signal indicating that the water level in the septic tank has reached a certain level.

=The following are ten things you should be aware of about your septic system.

Two Main Things toDo When the Alarm Goes Off?

First and foremost, there is no need to panic. Today’s septic systems are constructed in such a manner that you have ample time to cut water use and detect any issues prior to the system overflowing completely. The warning indicates that the water level has been raised, not that it would explode in a few seconds as some people believe. When the septic alarm goes off, do the following procedures immediately:

Locate the control panel on your computer. To turn off the alarm, press the button or flip the switch (if there is a sound). As you can see in the photo above, I didn’t have any sound because my phone was set to mute. Reduce your water use to a bare minimum until the problem has been fixed. Put your washing machine, dishwasher, and other water-using appliances on hold for the time being. And, if necessary, take a shower, but keep it brief

Why is My Water Level Elevated?

The majority of the time, your septic system alarm will sound because the level of water in your tank is more than it should be, according to the manufacturer. Let’s take a look at the most typical reasons behind this.

Power Problem

Electricity is used to run the pumps. Your pump will not be able to extract water from the tank if there is a power outage or any other power problem. In order to determine whether or not there is electricity to your sewage system, check the primary circuit breaker for your septic system. Check the pump circuit breaker in your control box if you have one; otherwise, proceed to step 3. That is also subject to error. This was, in fact, the source of my frustration. The system was never turned on for the first two weeks we were in our home, which was apparently due to a faulty installation by the electrician who installed it.

Also, make sure the outlets where the pump is connected in are working properly.

The problem is with the pump if the electricity is working, but the pump itself is not functioning properly.

Increased Water Usage

In order to function properly, your septic system must have a certain amount of capacity, and the pump must be configured to push water out of the system according to that capacity. If you are using much more water than normal, the level may rise. Performing an excessive amount of laundry, taking repeated showers if you have guests, or even cleaning a large number of dishes might raise the water level.

A similar situation exists when you clean excessively and use a lot of water. You are familiar with how much water you use on a regular basis, and you can readily detect this as a cause for the alarm to go off. Fortunately, if you return to regular usage, this issue should be resolved automatically.

Heavy Rain or Floods

It is possible that bad weather is the blame for your tank being full. Heavy rains or floods will cause the earth surrounding the tank to become saturated. The presence of standing water surrounding the tank, particularly if there are any cracks in the tank, increases the likelihood of water getting into it. Rainfall that is very heavy can also flood the earth around the drain field, preventing water from draining out of your septic system properly. You should restrict your water use to a bare minimum in this situation and wait until the soil dries out and the pump eliminates the extra water in the subsequent cycles before taking action.

Clogged Effluent Filter

Cleaning the effluent filter on a regular basis, generally twice a year, is recommended. Essentially, the filter serves as a screening barrier to reduce the volume of solid material that is discharged from a tank into a drain field, which in my instance is an underground system. On the tank’s discharge port is a filter that collects any debris. Solid waste might block the filter and cause the water to flow more slowly. The extra water will remain in the tank for a longer period of time than it should, and additional water will be added, raising the level.

Reduce water use and wait for a few pump cycles to check whether the problem has been resolved.

Pump or Float Failure

Some septic systems, such as mine, are fitted with submersible pumps that, in addition to the timer, are controlled by floats that control the pump. After reaching a certain height, the float will record the change and activate a pump to remove the water. The float is used to temporarily override the timer until the effluent in the tank returns to its regular level. If the float is not functioning properly, it will be unable to control the pump, resulting in the water level rising. The same may be said for a malfunctioning pump.

The pump must be maintained on a regular basis in order for the system to operate efficiently.

Find the control panel and turn it on. Change the mode of the switch to manual
If the pump is turned on and the water level lowers, the float is the source of the problem. This indicates that the pump is not starting properly
The fault is most likely the pump itself.

My view is that pump or float difficulties are not simple DIY fixes, and I would recommend consulting a professional.

What About the Blower Alarm

If you have a blower system, you may also have to deal with an additional alert to worry about. Aerobic septic tanks like mine, employ a blower mechanism to pump air into the treatment tank. By maintaining microorganisms that digest waste, this system assures the creation of oxygen necessary for the system’s operation.

Solids would not become liquids if this mechanism were not in place. If your blower alarm is going off, it’s possible that your blower is not working. I would contact a knowledgeable specialist to assist me in troubleshooting the situation.

Closing Thoughts

It’s crucial to note that some of these issues might be ongoing in nature. Consider upgrading your septic system, replacing any damaged components, or having them repaired if you discover that they are occurring too frequently. In any case, discussion with a specialist is required. These common issues frequently arise when there is a significant shift in the amount of water being consumed. Some new residents have just moved in, for example. Everyone now takes advantage of the shower, laundry, and dishwasher.

There is one thing that must be avoided at all costs: turning a blind eye to the situation.

It has the potential to cause the drain field to overflow.

All of these problems will cost a lot and will be more harder to solve than any of the smaller problems which contribute to rising sea level now.

Update: My Septic Alarm is Going Off Again

The alarm went off again one week after the septic system professional arrived to troubleshoot our situation. For starters, it was because the pump breaker was set to “off” that the problem occurred. The technician suspected that the electrician who had installed it may have forgotten to turn it back on once he had finished. He manually pumped the system and believed that this had resolved the issue. The alarm has sounded once more, but this time the pump breaker has been activated. I also tested the primary circuit breaker, which was found to be operational.

It should most likely be a problem with the pump or float, which is strange considering that this is a brand new system.

When the situation is resolved, I will make an update to this post.

We received another alert one week after the septic system specialist arrived to troubleshoot our issue. Due to the pump breaker being in the “off” position, the first problem occurred. The technician speculated that the electrician who installed it may have forgotten to turn it back on once he had finished. He manually pumped the system, believing that this would resolve the issue. This time, though, the alarm is activated by a tripped pump breaker. Lastly, I examined the main circuit breaker, which was turned on as well. There does not appear to be a problem with the power supply, but the water level is greater than it should be, indicating that the alarm switch is functioning correctly. Since this is a spanking new system, it’s most likely a pump or float issue, which is strange given the situation. Due to the fact that we are within one year of the construction warranty, I will contact the septic system firm to have them troubleshoot the problem. When the problem has been resolved, I will update the post.

Technician Came to Troubleshoot the Problem

He arrived and determined that there is nothing wrong with the septic tank system. According to him, we may have a leak somewhere in the home, most likely in one of the toilets. He physically pumped it till the water level had dropped to a safe level. I’m afraid I’ll have to disagree with him on this point. I checked all three of our toilets and found no signs of a leak at all. This septic system was intended to handle eight people, and there are presently just two individuals that live in the house.

In my opinion, the alert should not be turned off even if there is a minor leak.

I spoke with the builder, and he said he would call with the company’s management to get a sense of how things are going. I’ll add any new information to this page when it becomes available. Please let me know in the comments what you believe to be the source of the problem.

Update: A Manager Asked the Technician to Come Again

Following my conversation with the builder, the technician was requested to return to confirm that everything was functioning properly. In my previous statement, I said that there was no leak anyplace in the house. As a result, the problem had to be something else, and if we don’t repair it, it may happen again. He came to the conclusion that there could be a problem with the amount of wastewater that is discharged with each pumping cycle. Consequently, he raised that quantity a bit by changing the effluent control valve, which is represented in the illustration below.

Despite the fact that we recently used much more water due to the visit of my son and his girlfriend, I have not experienced any problems since then.

Posts related to this one:

Following my conversation with the builder, the technician was requested to return to the site to confirm that everything was functioning well. I agreed. There was no leak anyplace in the house, as I had said. Because of this, the problem had to be something else, and if we don’t repair it, it may happen again. His conclusion was that the volume of wastewater that is discharged with each pumping cycle might be the source of the problem. To remedy this, he raised the amount of effluent by a little amount, as seen in the illustration below. The problem, I hope, is no longer an issue. Because my son and his girlfriend came to visit us, we used substantially more water than usual, but I have not had any problems since then. To thank Scott for his remark below, in which he pointed out that I had neglected to update this section of the post, I’d want to express gratitude. In related news, here are some thoughts on

Septic Alarm Going Off? – Troubleshooting Delaware

WilleyCo installs alarm systems on a bit more than half of the residential septic systems in Delaware that are sold to homeowners. They may be put anywhere in the home, however they are most commonly seen outside near the septic tanks. When there is a problem, these alarm systems will emit a loud siren sound and illuminate a light to alert you. When the alarm goes off, what do you do with your time? To respond with an alarm occurrence effectively, you must first understand what the alert represents.

Alarm systems are equipped with float sensors, which are located within the pump tank.

What could cause the water level in the pump tank to rise to the level of the alarm float?

When anything isn’t operating properly with the sewage pump, your inside alarm will alert you. The alarm float has failed, and there is no electric current coming to the pump to replace it. It’s possible that a breaker has tripped. Examine your circuit breakers. Breakers can fail for a variety of reasons. If the pump isn’t on its own isolated breaker and another device attempted to consume electricity on the same circuit at the same time as the pump attempted to turn on, the pump may trip. Because to moisture intrusion, certain circuit breakers may trip. Have you dug anything up in the yard? It’s possible that you stepped on the wire, causing it to trip. In certain circumstances, a faulty wire may be the source of the tripped breaker

The pump also includes a float that determines when it may be turned on while waiting for the timer to be approved (see number 4). It’s possible that the float has gone bad. The lifetime of these floats is between 4 and 8 years. If the float has failed, the pump will not be aware that it needs to turn on
If the timer has failed or has been out of tune, the pump will not turn on. Many septic systems are equipped with a timer that signals to the pump float and pump when the system is permitted to use electricity. Timers are implemented to prevent the drainfield from being overused during high demand periods
Overuse of water is prevented by installing timers. This can occur in a variety of ways. Did you have a party, have guests over, or take a lengthy bath or shower while washing two loads of laundry at the same time? All of these factors might contribute to the accumulation of excess water in the pump tank between pump cycles. Take a look around the corner by the septic tanks. What if there is standing water over or around the tanks? It’s possible that surface and/or rainwater is entering into the pump tank’s reservoir. When the alarm is set off every time it rains, it becomes evident that something is wrong. When it comes to the worst-case situation, it is possible that the drainfield is experiencing difficulties absorbing water. This might occur for a variety of reasons. This might be caused by a damaged pipe, a broken fitting, or because the drainfield has been saturated with water and is unable to handle any more

What do you do?

Wait approximately 24 hours from the time the alarm began to sound and drastically cut your water consumption. This will give the system time to catch up if it is experiencing an increase in water use due to increased demand. Examine the septic breakers, particularly the one for the pump, for damage. If it has been tripped, it should be turned back on. You will need to speak with a septic contractor to determine why the breaker tripped in the first place
If it has just rained or is currently raining, look for standing water around the septic tanks. Are there any gutters that are pointing towards septic tanks? Is there any standing water near the tanks? If this is the case, take steps to correct the situation since it will shorten the lifespan of your septic system. If the alarm continues to sound after steps 1, 2, and 3 have been completed, call a septic contractor for assistance. Make sure to contact the installer if your equipment is still under warranty.

Is Your Septic System Alarm Going Off

septic alarm systems are designed to keep track of the water levels in the septic tank. They are intended to notify the user if the water level becomes too high or excessively low. As a result, if your alarm goes off or if you notice a red light on your alarm, this might signal that the water level is greater than typical. It is also possible that the problem is caused by a high level of sludge in the tank, in which case septic tank cleaning is usually sufficient to resolve the situation.

Why does the water level increase?

On most septic tanks, a timer has been built, which permits the pump to discharge wastewater into the leach field at predetermined intervals. The timer regulates the periods during which the pump is allowed to discharge wastewater from the system. If a large amount of water is utilized in between pumping cycles, the water has nowhere to go and will continue to rise within the tank until it is exhausted. Is your septic system sounding the alarm? Allow our septic system professionals to assist you.

What are the reasons for high water level in the tank?

It is possible that a high quantity of water in your septic tank system is caused by a variety of factors.

Failure of the sewage system to get electricity – Check your switchboard to verify whether the septic system is receiving power
Extreme water use (long showers, many laundry loads, and using the dishwasher more frequently than normal) might cause an overabundance of water to enter the septic system. Groundwater or rainfall can also collect around the septic system and leak into the tank
This is known as a backflow. It’s possible that the effluent filter is blocked. The effluent filters must be cleaned every six months, or sediments would collect in the filters and cause them to clog. This reduces the rate at which wastewater exits the system, resulting in an increase in the volume of water in the septic tank. Pumps are used in certain septic tanks to transport effluent to secondary wastewater treatment facilities. If the pump fails, the amount of water in the tank will rise as a result. The leach field can get blocked with effluent, which can cause the water level to rise as a result. It is also possible for the water level to rise due to mechanical faults with the air compressor, float switch, or other components. A high amount of sludge in the system can also be a contributing factor to this problem, which can be resolved by septic tank cleaning.

This problem can occur in anaerobic treatment systems owing to a malfunctioning aeration mechanism or a high water level in the aeration tank, among other things.

The frequency with which my septic system should be examined is not specified. What is the best way to determine when to pump out a septic tank?

What to do if the septic alarm goes off?

This should turn off the alarm if you press the red button on the alarm box or turn it on with the switch on it. Allow for 10-15 hours of continuous operation of the septic system, and the red light may turn off automatically. Take note that you should use less water during this period to assist the system in lowering the water level. If the red light turns off, this indicates that your system is operating properly.

Help – The red light is still on!

If the red light on your alarm won’t turn off, don’t get too worked up. Please contact Express Wastewater so that we can assist you in resolving the issue in a timely and professional manner. Emergency situations are given top priority, and we provide services across South-East Queensland. If your septic system requires immediate attention, please call us on 1300 722 517 or complete our online job booking form. When your septic alarm goes off, what should you do? Allow our professionals to assist you.

Not what you’re looking for?

More information about septic, sewage, and wastewater systems may be found by using the search box provided below.

Why Use Express Wastewater Solutions?

We are able to offer the optimum solution for your wastewater needs since we are not a manufacturer and are not bound to a certain technology.

EXPERT TEAM

Unlike manufacturers, we are not bound to any one system, which allows us to always provide the optimum solution for your wastewater requirements.

FREE 30 MINUTE WASTEWATER CONSULTATION

A free 30-minute phone consultation with one of our specialists will guide you through the process if you have never installed a home sewage treatment plant before
Thus, we provide this service to guide you through the process.

STREE FREE INSTALLATIONS

The entire wastewater installation process is handled by us
We can deal with all of the trades, the municipality, and everything else, so you don’t have to worry about a thing.

QUALIFIED, LICENSED PROFESSIONALS

Have confidence in the fact that Express is a team of certified and insured specialists that will do your task correctly the first time

FREE EXPERT ADVICE

Not sure which system is best for you, or want to know if your current system is up and running efficiently? Simply give one of our knowledgeable wastewater specialists a call, and they will be more than delighted to assist you

SAVE UP TO $10,000 ON REPAIRING YOUR SEPTIC SYSTEM

We will always attempt to fix your system rather than replacing it if it is not necessary to do so, which will normally save you a significant amount of money, often up to and beyond $10,000.

What is a Septic Tank Alarm System & What To Do If It’s Going Off.

Disclosure: This post contains affiliate links, which means that if you purchase a product after clicking on one of our links, we may receive a commission or free product from the firms featured in this post. Amazon is a good illustration of this. Depending on where your property has a septic tank put, there may be an alarm system installed for the tank anywhere in the house. What these alerts are used for and how they work will be discussed in greater detail in the following article.

Need Help With Your Septic Alarm or System Repair

So, what exactly is a septic tank alarm system, exactly? A septic tank alarm system is a device that monitors the water level inside the tank and sends you an alert if the water level rises higher than it should be. If the water level rises higher than it should be, this could be an indication of a problem with the septic tank pump, which is required in some systems. The effluent (wastewater) from the tank to the drainage field does not always require the use of a pump in all systems. A pump is not required in systems that are designed to siphon wastewater downhill from the tank to the drainage area utilizing gravity as the primary means of transport.

If you want to understand more about whether or not your septic system requires electricity, check out this article.

How Does a Septic Tank System Alarm Function?

To begin with, what is an alarm system for a septic tank? A septic tank alarm system is a device that monitors the water level inside the tank and sends you an alert if the water level rises higher than it should be. If the water level rises higher than it should be, this could indicate a problem with the septic tank pump, which is required in some systems. The effluent (wastewater) from the tank to the drainage field does not always require the use of a pump. There is no need for a pump in wastewater systems that are intended to siphon wastewater downhill from the tank to the drainage area.

Learn more about whether or not your septic system requires electricity by reading this article. This blog post will go into further detail on septic tank alarm systems, including how they work, why you might need one, and what to do if yours is on the blinking red light of death.

Septic Tank Alarm Systems for Electrical-Based Pumps

A Septic Tank System alarm is activated by the placement of a float inside the tank, which monitors the amount of water in the tank. Consider this to be analogous to the float at the bottom of your toilet tank. The float in your toilet tank monitors the amount of water in your tank, and when it reaches a certain level, it should shut off the water supply so that no more water goes into the tank. Similarly, the water level is monitored by the float on your alarm in a septic system, and the alarm will sound when the water level in the tank has increased to a predetermined level, signalling that there is a possible problem with the system.

Septic Tank Alarms for Aerobic Systems Compressor Pumps

If your property is equipped with an Aerobic-based system, you may additionally require a septic tank alarm. These systems circulate condensed air through the system in order to aid in the breakdown of the sewage in the treatment plant. Septic tank alarms are utilized in these sorts of systems to alert the user when there is a probable problem with the air pressure, which might signal that the compressor pump is not working properly.

Why Would You Need a Septic Tank Alarm System?

So, now that you have a clear grasp of what a Septic Tank Alarm System is and what it performs, you may be wondering why you would need one. Keep in mind that the alarm is intended to notify you of a problem with your septic system that might lead to more serious issues down the line if not addressed. The purpose of the warning is to have the problems resolved before anything catastrophic occurs. For illustration purposes, consider a pumping system that is powered by electricity and is responsible for pumping effluent (wastewater) from a septic tank upwards to a drainage area.

(This is very frequent.) Consequently, a pump powered by electricity is installed in the tank to either pump the water out of the tank at certain intervals or when the water level reaches an established level.

In case the pump fails for whatever reason, the alarm will sound to inform you that there is too much water in the tank, resulting in an increase in the water level in the tank and an alarm being triggered.

The Alarm in an Aerobic System

Additionally, the Alarm in an Aerobic System will notify you if the compressor pump is not functioning correctly, which means that sufficient air is not being introduced into system to allow for decomposition of the waste to occur. In the event that your system has any form of pump component, it is a good idea to have a functional alarm installed.

Where is Your Septic Tank Alarm System Located?

The alarm for your septic tank may be positioned in a number of different locations.

If you hear your alarm go off, look in the following places to see if you can find where it came from. Avoid being alarmed since there is no fire or carbon monoxide alarm! Your septic tank alarm may be positioned in one of the following locations, starting with the first:

On the tank’s side, it says: The connection is made to the side of your house. You have a basement
In a utility closet, if you will

What does it Mean if My Septic Tank Alarm is Going off?

What does it imply if the alarm on your septic tank is sounding off? Essentially, if your septic tank alarm is going off, it means that the alarm is detecting an incorrect water level in the septic tank, a problem with the pump in the septic tank for electrically assisted pumping systems, or a problem with the air pressure in the compressor pump of your Aerobic Septic System. But don’t be alarmed; there are a few other possibilities for why your alarm is going off than a complete pump failure.

What to Do if Your Septic Alarm is Going Off?

When an alarm goes off, you undoubtedly want to know what to do next to assist diagnose the potential problem with your septic tank system. Here’s what you should do next. As soon as you hear your alarm go off, take the following steps:

Locate the alarm
If you are unsure of its placement, refer to the section above for some frequent locations for septic tank alarms. If your alarm system includes an audible alarm, it should feature a button to stop the alert or to turn on the alarm system. This button can be used to turn off the alarm system. It is important to note that the Red Light on the alarm will remain illuminated until the problem is rectified. The silent button just prevents you from going insane as a result of the noise. When it comes to wiring your septic alarm system, it should be connected to a different breaker than the actual pump that it is monitoring. So the next step is to identify the pump’s circuit breaker and check sure it hasn’t been tripped by anything. Some of these breakers can trip or be switched off by mistake, preventing the pump from going on and pumping out the remaining liquid in the storage container. It is possible that this might cause the water level to increase over the acceptable level, causing the alarm to sound. Simply re-energize your circuit breaker and the pump should begin to function again, draining the water from the access line again. It is possible that one of the floats will have a fault, causing you to receive a false positive on the water level. Assuming you are comfortable doing so, check to see that your floats are securely attached and operating correctly
If you discover that your pump or aerator is not running properly, you can either repair them yourself or contact a local septic firm for assistance.

How to Test Your Septic Alarm?

To ensure that your septic tank alarm is functioning properly, it is recommended that you test it on a regular basis. To be on the safe side, I would recommend once every six months; obviously, the more frequently, the better. The process of testing your septic tank alarm is typically rather simple. Each septic tank alarm should be equipped with a test switch, which you may use to quickly check the alarm’s functionality. To see how to test your septic tank alarm, watch the video below.