Go to your basement or crawl space, and then look for the main sewer line that leads to your septic tank. Look for a pipe that’s roughly four inches in diameter that leads away from your house. Remember the location of the sewer pipe and where the pipe leaves your home so you can find it outside.
How do I know if my septic has a pump?
One positive indication that your septic tank needs pumping is water pooling on the surface over the tank and its drain field. A full septic tank can carry solid scrap into the drain field, clogging leach-field passages. The wastewater leaks out of the tank and pipe joints in the drain field and flows to the surface.
Are septic tank locations public record?
Contact your local health department for public records. These permits should come with a diagram of the location where the septic system is buried. Depending on the age of your septic system, you may be able to find information regarding the location of your septic system by making a public records request.
Where are most septic tanks located?
Toe the Line. Your septic tank will most certainly be installed along the main sewer line that runs out of your home. Look for the 4-inch sewer that exits the crawl space or basement, and locate the same spot outside the home. Septic tanks are usually located between ten to 25 feet away from the home.
Can a metal detector find a septic tank?
If it’s Concrete or Steel, Use a Metal Detector. Based on your conclusions in Step 3, if your septic tank is likely made from concrete or steel, a metal detector can make the task of locating it much easier. But not just any metal detector will do.
How do I know if my septic pump is not working?
One of our technicians will wire the float switch to an alarm panel that sounds if the pump fails. Without a functioning pump, the sewage level continues to rise and the alarm lets you know the waste isn’t being removed from the tank. This alarm will sound and alert you before a sewage backup occurs.
Do all septic tanks have pumps?
Septic Systems Rely on Gravity, Most of the Time For that to work, a pump is needed, or sometimes two pumps. If the tank is higher than the house, a grinder pump that liquefies solids will be placed in a pit in the home’s basement or crawlspace.
How do I find my septic tank lid?
You can locate the lid of your septic tank by poking the ground every few feet with a metal probe. Lids can be buried up to a foot deep on average, so be sure to investigate any bumps that may indicate something is buried underneath.
How do I find out if my septic tank is registered?
Check if your septic tank is already registered You can check if your tank has already been registered by contacting your environmental regulator. If you are unsure then it is best to check and avoid making an unnecessary payment. The NIEA and SEPA have records of all registered septic tanks.
Do I have to change my septic tank?
Under the new rules, if you have a specific septic tank that discharges to surface water (river, stream, ditch, etc.) you are required to upgrade or replace your septic tank treatment system to a full sewage treatment plant by 2020, or when you sell a property, if it’s prior to this date.
How much does it cost to pump a septic tank?
How much does it cost to pump out a septic tank? The average cost is $300, but can run up to $500, depending on your location. The tank should be pumped out every three to five years.
How often should a septic tank be pumped?
Inspect and Pump Frequently The average household septic system should be inspected at least every three years by a septic service professional. Household septic tanks are typically pumped every three to five years.
How deep should a septic tank be buried?
In most cases, septic tank components including the lid, are buried between 4 inches and 4 feet underground. You can use a metal probe to locate its edges and mark the perimeter. If you do not find the lid by probing, shallow excavation with a shovel along the tank’s perimeter should reveal the lid.
Can I drive over my leach field?
Can You Drive on a Septic Drain Field? No, driving over your septic drain field is similarly never ever recommended. As much as you are able to help it, prevent cars or heavy equipment (such as oil delivery trucks, swimming pool water trucks, cement mixers, and also the like) to drive straight over the field.
Can you use a metal detector to find sewer lines?
Using a Plumbing Pipe Detector to Locate Underground Pipes. As a property owner there will be times when, for a variety of reasons, you will need to locate underground metal objects. For example, using a pipe locator metal detector you can easily pinpoint leaking underground pipes quickly.
Are septic tanks made of metal?
The majority of septic tanks are constructed out of concrete, fiberglass, polyethylene or coated steel. Typically, septic tanks with a capacity smaller than 6,000 gallons are pre-manufactured. Larger septic tanks are constructed in place or assembled on-site from pre-manufactured sections.
How To Find Septic Tank Location: A Guide for Property Owners
The majority of individuals prefer to relax on their back patio or porch and take in the scenery rather than worrying about where their septic tank could be. When you know exactly where your septic tank is, it will be much easier to schedule routine sewer line cleanouts and repair appointments. Continue reading to find out more about how to locate your septic tank.
Follow the Main Sewer Line
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your property. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about down there. Look for a pipe with a diameter of around four inches that is leading away from your home or building. Keep a note of the position of the sewer pipe and the point at which the line exits your home so that you can locate it outdoors.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your home.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may have to probe a bit further out before striking the tank.
Inspect Your Property
Purchase a soil probe that you may use to probe into the earth in order to locate the underground sewage line and septic tank in your yard. Find the main sewage line that leads to your septic tank by going to your basement or crawl space and digging about in it. Look for a pipe with a diameter of around four inches that is leading away from your home or business. Recall where your sewer pipe is located, as well as where it exits your home, in order to locate it while you are out in the field.
If you have a drain snake, you may use it to try to follow the approximate course of the pipes in your house.
Since the majority of states require at least five feet between a home’s septic tank and its foundation, with many tanks located between 10 and 25 feet away, you may need to probe a bit further out before striking the tank.
- Paved surfaces
- Unique landscaping
- Your water well, if you have one
- And other features.
If you are still having trouble locating your septic system, you might inquire of your neighbors about the location of their septic tank on their land. Finding out how far away their septic systems are will help you figure out where yours might be hidden in your yard or garden.
Check the Property Records
Are you unsure about how to obtain this? Simply contact your county’s health department for further information. Check with your local health agency to see if they have a property survey map and a septic tank map that you can borrow. Perhaps you will be shocked to learn that there are a variety of options to obtain information about your property without ever leaving the comfort of your own residence. Building permits, for example, are frequently found in county records, and they may provide schematics with specifications on how far away from a septic tank a home should be, as well as other important information such as the size of the tank.
Most counties, on the other hand, keep records of septic tank installations for every address. For further information on the placement of your septic tank, you can consult your home inspection documents or the deed to the property.
Don’t Try to Fix Septic Tank Issues Yourself
Septic tank problems should be left to the specialists. The Original Plumber can do routine maintenance on your septic tank and examine any problems you may have once you’ve located the tank. It is not recommended to open the septic tank lid since poisonous vapors might cause major health problems. Getting trapped in an open septic tank might result in serious injury or death. While it is beneficial to know where your septic tank is located, it is also beneficial to be aware of the potential health dangers associated with opening the tank.
Schedule Septic Tank Maintenance
The maintenance of your septic tank on a regular basis helps to avoid sewer backups and costly repairs to your sewer system. You should plan to have your septic tank pumped out every three to five years, depending on the size of your tank and the number of people that reside in your home. The Original Plumber offers skilled septic tank and drain field maintenance and repair services at competitive prices. While it is useful to know where the septic tank is located, it is not required. Our team of skilled plumbers is equipped with all of the tools and equipment necessary to locate your tank, even if you have a vast property.
We are open seven days a week, twenty-four hours a day.
Frequently Asked Questions
A septic system is a system for the management of wastewater. Simply said, wastewater will exit your home through pipes until it reaches your septic tank, which is located outside your home. Septic tanks are normally located beneath the surface of the earth. Solids and liquids will separate in the septic tank as a result of the separation process. Eventually, the solids will fall to the bottom of the tank and the liquids will run out onto your leach field.
How do I know if I have a septic tank?
Even if there are no obvious signs of a septic tank in your yard – such as uneven landscaping – there are a few techniques to assess whether or not your home is equipped with an onsite sewage system. Checking your property records is the most reliable technique to ensure that you are utilizing the correct system. When you acquired your house, you should have received a copy of the septic system map with the property documents as well. Checking your electricity statement is another way to determine this.
If you’re also using well water, it’s possible that you won’t receive one at all.
What do I do once I locate my septic tank?
If there are no visible signs that you may have a septic tank – such as uneven landscaping in your yard – there are a few ways to find out if you do or do not have a septic tank. Checking your property records is the most reliable way to ensure that you are using the correct equipment. When you purchased your home, you should have received a map of the septic system with the property records. Checking your utility bill is another way to determine this information. The public utility services should not issue you a water bill because your septic system is part of your wastewater management system.
In fact, if you’re also using well water, you might not even get one. It is likely that you are connected to well water rather than the public sewer system if you do not have a meter attached to your water supply.
How To Find My Septic Tank
- What is a septic tank
- How do I know if I have a septic tank
- And how do I know if I have a septic tank Identifying the location of your septic tank is critical for several reasons. The Best Way to Find a Septic Tank
- What to Do Once You’ve Discovered Your Septic Tank
You may have fallen in love with your new house because of its appealing good looks and characteristics, but there is almost certainly more to your new home than meets the eye. In many cases, the characteristics that make your house run more effectively and allow you to live a pleasant, contemporary life are not readily apparent. Septic tanks, for example, are an important part of your home’s infrastructure. A septic system is responsible for regulating and managing the wastewater generated by your home.
- “How can I locate my septic tank?” is one of the most often requested inquiries we receive.
- When your tank’s lid is difficult to locate – especially if you are not the original homeowner – you may be at a loss for what to do or where to look for the lid when you need it.
- The majority of the time, all of the components of the septic tank are buried between four inches and four feet below ground level.
- In order to do so, it is necessary to first comprehend the functions of septic tanks and septic systems and why it is important to know where yours is located.
How to Locate Your Septic Tank
Your septic tank’s location is not a closely guarded secret. There will be a method for you to locate it and make a note of its position for future reference, and below are a few examples of such methods.
What Is a Septic Tank?
Having a functioning septic tank is an important aspect of having an effective septic system. In the United States, around 20% of households utilize a septic system to handle their wastewater. Houses in rural parts of New England are the most likely to have a septic system, with residences in the Eastern United States being the most prevalent location for septic systems. When there are few and far between residences, it is typically more efficient and cost-effective to employ a septic system to manage wastewater rather than relying on a public sewage system to handle waste water.
Typically, a septic tank is a container that is waterproof and composed of a material such as concrete, polyethylene, fiberglass, or a combination of these.
An important function of a septic tank is to hold on to wastewater until any particulates in the water separate themselves from the water.
Any liquid that remains in the tank eventually drains into a leach field or a drainfield, where it is known as “effluent.” The dirt in the leach field aids in the filtering of the water and the removal of bacteria, viruses, and other pollutants that may be present in it.
Septic tanks erected in Onondaga County must contain input and outlet baffles, as well as an effluent filter or sanitary tees, in order to effectively separate particles from liquids during the treatment process.
How Do I Know If I Have a Septic Tank?
What is the best way to tell if your home has a septic tank? There are generally a few of different methods to tell. Examining your water bill might help you identify whether or not your house is served by a septic system or is part of the public sewage system in your neighborhood. If you have a septic system for wastewater management, you are likely to receive a charge from the utility provider for wastewater or sewer services of zero dollars. In the case of those who are fortunate enough to have a septic system, it is likely that they may not receive any water bills at all.
- A lack of a meter on the water line that enters your property is typically indicative of the fact that you are utilizing well water rather than public utility water, according to the National Association of Realtors.
- A septic system is likely to be installed in your home if you reside in a rather rural location.
- Septic systems are likely to be installed in all of these buildings, which means your home is likely to be as well.
- When a septic tank is present, it is common to find a mound or tiny hill on the property that is not a natural structure.
- Checking your property records is a foolproof method of determining whether or not your home is equipped with a septic system.
Why It’s Important to Know the Location of Your Septic Tank
You might wonder why you should bother trying to discover out where your septic tank is. There are several important reasons for this:
1. To Be Able to Care for It Properly
The first reason you should try to locate your septic tank is that knowing where it is will help you to properly repair and care for it in the future. The standard guideline is to avoid erecting structures or placing heavy objects on top of the septic tank. It’s possible that you don’t want to park your car or truck on top of it, and you don’t want visitors to your house to park their cars on top of it, either. Due to the weight of the automobiles, there is a possibility that the tank would collapse due to excessive pressure.
2. If You Want to Landscape or Remodel Your Property
If you want to build an addition to your home or perform some landscaping around your property, you will need to know where your septic tank is located. Nothing with deep or lengthy roots should be planted on top of or in the area of your tank, since this can cause problems. If roots are allowed to grow into the pipes of your septic system, it is conceivable that your system will get clogged. When you know where the tank is going to be, you may arrange your landscaping such that only shallow-rooted plants, such as grass, are in close proximity to the tank.
For starters, the tank’s weight might lead it to collapse due to the weight of the construction. A second issue is that getting access to the tank becomes more difficult if a permanent building has been constructed on top of it.
3. If a Problem With Your Tank Occurs
Knowing where your tank is buried might also assist you in identifying problems as soon as they arise. Consider the following scenario: you wake up one morning and see that there is flooding or ponding water in the region surrounding your septic tank – a sign that your system is overwhelmed and that an excessive amount of water is being utilized all at once.
4. Ease of Getting It Fixed
Once you have determined the location of your sewer system, you can quickly send a plumber to it in the event that something goes wrong with the system, saving everyone both time and money. Get in Touch With A Plumber Right Away
1. Use a Septic Tank Map
First and foremost, make use of a road map. Using a map is frequently the quickest and most convenient alternative. Most counties keep records of the installation of septic tanks at all of their residents’ residences. These maps should include schematics that illustrate the specific placement of the tank on the land, as well as measurements that allow you to measure and locate the tank’s exact location on the property. Never mind that landmarks may shift over time depending on when the tank was built, so if there are a few more shrubs or a tree nearby, don’t rule out that location as a possibility.
- If you are unable to locate a map or other paperwork that identifies the location of your septic tank, there are a few locations to try to see if you can obtain a map of the area.
- The county health department is responsible for keeping track of septic systems.
- A septic tank’s position could be depicted on a survey map, for example.
- The creation of your own map and documentation may be worthwhile if you cannot locate a map or blueprint of your property and nothing appears to be on file regarding it at the county health department or another municipal agency.
2. Follow the Pipes to Find Your Septic Tank
Whether or not there is an existing map of your septic tank on file, or whether or not you choose to develop one for future reference or for future homeowners, you will still need to track down and find the tank. One method of accomplishing this is to follow the sewer lines that lead away from your residence. The septic tank is situated along the sewage line that goes from your home and into the yard, as we’re sure you’re aware. Find a four-inch sewer pipe in your basement or crawl space. This is the line that will lead to your septic system and should be accessible from the ground level.
- In general, though, you’re searching for a pipe with a diameter of four inches or more that leaves your home via a basement wall or ceiling.
- By inserting a thin metal probe (also known as a soil probe) into the earth near the sewage line, you can track the pipe’s location.
- The majority of septic tanks are located between 10 and 25 feet away from your home, and they cannot be any closer than five feet.
- Going via the sewage line itself is another method of locating the septic tank utilizing it.
- Drain snakes are typically used to unclog clogs in toilets and drains, and they may be used to do the same thing.
- When the snake comes to a complete halt, it has almost certainly reached the tank.
- While drawing the snake back, make a note of how far it has been extended and whether it has made any bends or turns.
- When looking for your septic tank, you may use a transmitter that you flush down the toilet and it will direct you straight to the tank.
If you only want to keep an eye on the condition of your tank and don’t need to dig it up and inspect it, you may thread a pipe camera into the sewer pipe to see what’s happening.
3. Inspect Your Yard
Septic tanks are designed to be as unobtrusive as possible when they are erected. With the passage of time, and the growth of the grass, it might be difficult to discern the visual indications that indicated the exact location of your septic tank’s installation. However, this does not rule out the possibility of finding evidence that will take you to the location of your septic tank in the future. First and foremost, you want to rule out any potential locations for your septic tank, such as:
- Under a road or similar paved surface, for example. Right up against the house (the tank must be at least five feet away)
- Directly in front of the home Immediately adjacent to your well (if you have one)
- In close proximity to trees or densely planted regions
- In the shadow of a patio, deck, or other building
Once you’ve ruled out any potential locations for your tank, it’s time to start hunting for indications as to where it may be hiding in plain sight. Keep your eyes peeled as you go about your property, looking for any inexplicable high or low points that might suggest the presence of an underground tank. When looking at your property, you could see a hill or mound on the ground, which is frequently an indication that there is a septic tank nearby. One further item to consider while searching for the right septic tank for your home is the amount of grass or other foliage in your yard.
Alternatively, if the tank was not adequately buried, you may observe a “bald patch,” which is an area where the grass is struggling to grow in the vicinity.
4. Talk to Your Neighbors
If your neighbors have septic systems as well, they may be able to assist you in locating your tank. Inquire of your neighbors about the location of their septic tanks in relation to their residences. Having a polite conversation with your neighbors regarding septic systems not only provides you with a means to figure out where yours is, but it may also serve as a friendly introduction to the other residents of your community.
5. Look for Your Septic Tank Lid
It is only the first step in the process to discover where your septic tank is located. After you’ve located your tank, the following step is to locate the lid. You can locate it with the help of your soil probe. The majority of septic tanks are rectangular in shape and measure around five feet by eight feet. The perimeter of the tank should be marked with a probe once it has been probed around. A shallow excavation with a shovel within the tank’s perimeter and near the center (or broken into halves for a two compartment tank) should show the position of the lid or lids if you are unable to feel them by probing.
The tank itself is likely to be filled with foul-smelling vapors, if not potentially hazardous ones.
What to Do After You Find Your Septic Tank
Once you’ve determined where your tank is, it’s time to bring in the specialists. Trust us when we say that opening a septic tank is not something that just anybody wants to undertake. Concrete septic tank lids are extremely heavy and must be lifted using special lifting gear in order to be removed. Since the vapors are potentially dangerous due to the contents of the tank, please respect our advice and refrain from attempting to open the tank yourself. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, it might be lethal owing to the toxicity of the sewage in the tank.
However, before you send in a team of experienced plumbers, there are a few things you can do to ensure that others do not experience the same difficulty locating the tank and to make locating the tank in the future easier.
1. Mark Its Location
The pros should be contacted as soon as you’ve discovered your tank. a. Don’t kid yourself, draining and cleaning a septic tank is not something that just anybody wants to undertake. A special lifting equipment is required to remove concrete septic tank lids since they are quite heavy. Because of the contents, the gases can be poisonous; thus, please respect our warning and do not attempt to open the tank on your own own. An exposed septic tank can be hazardous to anybody wandering around your property’s perimeter, and if someone were to fall into it, the toxicity of the waste might be lethal.
2. Take Care of Your Septic Tank
Taking proper care of your tank may save you hundreds of dollars over the course of its lifetime. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water overall. Things like paper towels, face wipes, and cat litter should not be flushed down the toilet since they are not designed to be flushed.
In addition, installing low-flow faucets and high-efficiency toilets can help you reduce the amount of water used in your home.
For example, you don’t want to be washing load after load of laundry or running your clothes washer at the same time as your dishwasher all at the same time.
Call a Professional Plumber
Taking proper care of your tank may save you thousands of dollars over the course of its useful life span. The expense of maintaining your system could be a few hundred dollars every few years, but that’s a lot less than the thousands of dollars it might cost to repair or replace a damaged tank or a malfunctioning septic system in most cases. Two strategies to take better care of your septic tank and system are to avoid utilizing your drain pipes or toilets as garbage cans and to use less water in general.
Solid meals, cooking oil, and pharmaceuticals should not be flushed down the sink drain in your kitchen.
The usage of water-intensive equipment should be avoided wherever possible, according to another proposal. It’s best not to do things like washing loads of laundry after loads of laundry or running the clothes washer at the same time as the dishwasher.
How to Locate Your Septic Tank
It may seem impossible to imagine that one of the largest and most visible elements of your whole plumbing system is also one of the most difficult to locate, but when your property is served by a septic system, this is perfectly true. A strong explanation for this is because septic tanks are huge, unattractive, stink horrible and give off an unwarranted impression of dirt. Not only does burying them underground assist to prevent them from harm, but it also provides you with additional useable space on your property and conceals what would otherwise be a blight on your landscape.
This site is dedicated to assisting you in locating your septic system without the need for any time-consuming digging.
How To Find A Septic Tank: Step By Step
It is critical to maintain the health of your septic tank since it is responsible for securely storing and handling the wastewater that drains from your house. It is necessary to pump your septic tank once every 1-3 years, depending on the number of people living in your household and the size of your tank, in order to avoid septic tank repairs or early failure, which means you must be familiar with the location of your tank. It’s not often simple to identify your septic tank, and many plumbers charge extra for this service, which is especially true if your tank’s lid is buried beneath.
1. Gather Some Helpful Tools
Septic tank location may be made much easier with the use of several simple instruments and techniques. To locate your septic tank, you only need to know the following information: A soil probe is one of the most useful instruments for locating a septic tank. It is a tiny piece of metal that is used to puncture through the earth and detect anything that could be buried underneath. Start at the point where your sewage line exits your home and work your way straight out, inserting your soil probe every two feet along the way.
Using this method, you may also locate the cover for your septic tank.
While we highly advise keeping your cover clean and exposed in the event that you require emergency septic service, we recognize that this is not always the case.
2. Use a Septic Tank Map
If you are a new homeowner who is trying to figure out where your septic tank is, a septic tank map should be included in your inspection documentation.
You can use this information to assist you in pinpointing the exact position of your storage tank. If you don’t have access to this map, there are a few of additional strategies you might employ.
3. Start Ruling Areas Out
The location of a septic tank cannot be constructed in specific areas due to the risk of causing major damage to your property or tank, as specified by local rules. Your septic tank will not be affected by the following:
- Immediately adjacent to your well
- Beneath your home
- Directly against your home
- For example, underneath your driveway
- Under trees
- And other locations. Structures like a patio or deck are good examples of this.
4. Inspect Your Property
If you take a hard look around your land, there’s a high possibility you’ll be able to locate your septic tank without having to do any probing whatsoever. In many circumstances, a septic tank may be identified by a slight dip or slope on your land that cannot be explained by any other means. Due to the fact that the hole that your contractors excavated for your septic tank may not have been exactly the proper size, they proceeded to install the tank anyhow. This is a rather regular occurrence.
When there is a minor divot or depression, it indicates that the hole was too large and that your contractors simply did not fill the depression to level the hole.
The likelihood of your septic tank being discovered in a few specific locations is quite high.
- Your water well, if you have one (for a variety of reasons that are rather clear)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built and no one performed a proper inspection before it was built)
- Any paved surfaces (it won’t be under a driveway, sidewalk, or patio unless they were added after the home was built and no one conducted a proper inspection before it was built)
- Any paved surfaces (it won’t be under a patio, sidewalk, or driveway unless they were added after the home was built If there is any particular landscaping
5. Inspect Your Yard
A comprehensive investigation of your yard may be necessary to discover your septic tank considerably more quickly in some cases. The following are important items to check for in your yard:
- If your septic tank is overfilled, sewage can leak out into the ground and function as fertilizer for your lawn, resulting in lush green grass. A area of grass that is very lush and green is a good sign that your septic tank is just beneath it
- Puddles that don’t make sense: If your septic tank is seriously overfilled, it is possible that water will pool on your grass. Another telltale indicator that your septic tank is below ground level is an unexplainable pool of water. Ground that is uneven: When installing septic tanks, it is possible that the contractors will mistakenly create high or low patches on your grass. If you come across any uneven terrain, it’s possible that your septic tank is right there.
The metal soil probe can let you find out for certain whether or not your septic tank is located in a certain area of your yard or not. As soon as your metal soil probe makes contact with the tank, you may use your shovel to dig out the grass surrounding it and discover the septic tank lid.
6. Follow Your Sewer Main/Sewer Pipes
Following your sewage lines is one of the most straightforward methods of locating your septic tank. These pipes have a diameter of roughly 4 inches and are commonly found in the basement or crawlspace of your house. They are not dangerous. Following the pipes from your house out into your yard, using your metal soil probe every 2 feet or so until you reach the tank, is a simple process once they are located. Aside from that, every drain in your home is connected to your sewage main, which in turn is connected to your septic tank.
The likelihood that one of your major sewer lines is located in your basement or crawlspace is high if you have exposed plumbing lines in your basement or crawlspace.
If the line is labeled, it is usually made of plastic or rubber. It is important to determine where this line exits your property and in which direction it is moving, as it often travels straight out to the septic tank itself.
7. Check Your Property Records
Lastly, if all else fails, a search of your property’s public records will almost certainly reveal the location of the tank you’re looking for. Your builders most likely secured a permit for your property because septic systems are required to be installed by law in every state. In order to do so, they had to develop a thorough plan that depicted your property as well as the exact location where they intended to construct the tank. This is done to ensure that the local health department is aware of the tank and is prepared to deal with any issues that may arise as a result of its presence.
If you look hard enough, you may be able to locate the original building records for your home without ever having to get in your car or visit your local records center.
What to Do Once You Find Your Septic Tank
Upon discovering the position of your septic tank, you should mark its location on a map of your property. Use something to indicate the location of your lid, such as an attractive garden item that can’t be changed, to help you locate it. A birdbath, a rock, or a potted plant are just a few of the possibilities. You are now ready to arrange your septic tank inspection and pumping service. Contact us now! If you have any more concerns regarding how to locate your septic tank, or if you want septic tank servicing, please contact The Plumbing Experts at (864) 210-3127 right now!
How Do I Find My Septic Tank
What is the location of my septic tank? Natalie Cooper is a model and actress who has appeared in a number of films and television shows. 2019-10-24T 02:52:07+10:00
How Do I Find My Septic Tank
Whether or not my property has a septic tank is up in the air. If you live on an acreage or in a rural region, it is highly probable that you have a septic tank or a waste water treatment system in your home. What Is the Appearance of a Septic Tank? The great majority of septic tanks are 1600L concrete tanks, which are common in the industry. They feature a spherical concrete top with a huge lid in the center and two little lids on the sides. They are made out of concrete. Although the lids of these tanks may have been removed or modified on occasion, this is a rare occurrence.
A tiny proportion of septic tanks have a capacity of 3000L or more.
Our expert lifts the hefty lid of a 3000L septic tank and inspects the contents.
If you have discovered a tank or tanks that do not appear to be part of a waste water treatment plant system, it is possible that you have discovered a septic tank system. To learn more about our wastewater treatment plant, please visit our Waste Water Treatment Plant website.
How Can I Find My Septic Tank?
According to standard guidelines, the septic tank should be positioned close to the home, preferably on the same side of the house as the toilet. It can be found on the grass or within a garden bed, depending on its location. Going outdoors to the same side of the home as the toilet and performing a visual check of the septic tank is a smart first step to taking in order to discover where your septic tank is. The location of the toilets from outside can be determined if you are unfamiliar with the location of the toilets (for example, if you are looking to purchase a property).
Unfortunately, the position of septic tanks can vary widely and is not always easily discernible from the surrounding landscape.
In cases where the septic tank is no longer visible, it is likely that it has become overgrown with grass, has been buried in a garden or has had a garden built over it, that an outdoor area has been added and the septic tank has been paved over, or that a deck has been constructed on top of the tank.
- They should indicate the position of your septic tank, as well as the location of your grease trap and greywater tank, if any.
- Alternatively, if we have previously serviced the property for a different owner, our helpful office staff can examine our records to see if there are any notes pertaining to the site.
- A specific gadget is used to locate the location of the septic tank, and our professional will mark the location of the tank so that it may be exposed and cleaned out.
- Using an electronic service locator, you may locate a septic tank.
- In the event that you’re not experiencing any problems, the toilets are flushing normally, and there are no foul odors, you may ponder whether it’s best to leave things alone rather than attempting to locate and unburden a hidden septic tank.
- Although you could wait until there is a problem, this would almost certainly result in a significant amount of additional charges.
- Does it make sense for me to have many toilets and also multiple septic tanks?
It is decided by the number of bedrooms, which in turn determines the number of people who are anticipated to reside in the house, that the size of the septic tank should be. The following is the relationship between septic tank volumes and the number of bedrooms:
- There are three sizes of sewer tanks available: 3000L for three bedrooms, 3500L for four bedrooms, and 4000L for five bedrooms.
The most typical septic tank size is 1600L, although there are also some 3000L septic tanks available on the market. It is possible to have septic tanks with capacities as large as 3500L or 4000L, although they are not as popular, and most residences that require these capacities have numerous septic tanks in order to meet the septic litre requirements for each bedroom. Using the septic tank lid as a test, you may quickly determine whether all of the toilets in your home are linked to the same septic tank.
Check the rest of the toilets in the home by repeating the procedure.
Please call us immediately to have your septic tank pumped out or to schedule a free septic tank test when we are next in your area.
a link to the page’s load
How to Locate a Septic Tank
A surprising number of homeowners have had to figure out how to find the location of a septic tank on their premises. If you’re purchasing a home with a septic system or discover that your property’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point in time. In the course of a real estate transaction, the property owners or real estate agent may be aware of the location of the tank. Inquire about the “as-built,” which is a schematic of the septic system and the specifics of its installation.
Unfortunately, locating the septic tank may not be as simple as it appears.
Because septic system permits have only been needed in Oregon since 1972, you may have to depend on visual indicators to determine whether your system is working properly.
1.Follow the Outgoing Sewer Pipe
Many homeowners, to their surprise, have had to figure out where their septic tank is located on their property. Whether you’re buying a home with a septic system or discovering that your home’s tank hasn’t been maintained in years, you’ll want to know where the tank is located because all septic tanks must be pumped at some point. It’s possible that the property owners or real estate agent will know where the tank is located during a real estate transaction. Obtain a “as-built,” which is a schematic of the septic system and the specifics of how it will be installed.
Unluckily, locating the septic tank may not be a simple process. It was not always necessary to file an as-built with the local health authority. You may have to depend on visual signals because septic system permits in Oregon have only been needed since 1972.
2.Search for Septic Tank Risers and Lids
Depending on their age, septic tanks are either one- or two-compartment structures. Each compartment has a cover, with two additional lids for dual-compartment tanks that were added later. If the tank includes an access point known as a riser, the lid may be readily visible from outside. Look for round, plastic discs that are about a foot or two in diameter. Due to the fact that the lids might be flush with the ground or just a few inches above it, they can get overrun with grass and other plants over time.
Tanks without risers are likewise equipped with lids, however they are located underground.
3.Find the Drain Field First
In the absence of a riser and lid, search for indicators of a drain field, such as an area of grass that grows more quickly or more slowly than the rest of the yard, grass that is a different color from the rest of the yard, or areas where snow melts more quickly than in other parts of the yard. Spots of high or low ground in the yard might possibly indicate the presence of a subterranean tank or drain field. You will be able to discover the tank if you probe these regions.
Reasons to Hire a Contractor for Help
Attempting to locate a septic tank on your own can be risky, and in some cases, lethal, if the septic system is old and in danger of collapse. In the event that you fall into a cesspool, dry well, or septic tank, you will die. Removing septic tank lids on your own might potentially put you at risk of contracting bacterial or virus diseases. If you detect any of the following issues, please contact a contractor to assist you in locating or inspecting your septic tank:
- Soil that is sinking around the tank or drain field. Drainage backup into the home’s sewer system, or toilet backup
- A foul odor in the area where you assume the tank and drain field are located
- When there is no rain, pooling water, muddy soil, or spongy grass might occur. Septic tank covers that are rusted, cracked, or have been replaced with improvised lids are prohibited.
Even though you may be ashamed about forgetting where your septic tank is, it is a very frequent problem among homeowners. A contractor may assist you in locating it, and he or she may do it as part of the pumping service. If you need assistance locating your tank or if you have any other questions, please contact us at 503-630-7802. We are available to assist you!
How to Find Your Septic Tank
Over time, all septic tanks become clogged with sediments and must be pumped out in order to continue functioning properly. Septic tank lids are frequently located at ground level. The majority of the time, they have been buried anywhere between four inches and four feet underground. In the event that you have recently purchased a property and are unsure as to where your septic tank is located, this article will give instructions on how to identify your septic tank. Noteworthy: While every property is unique, septic tanks are usually typically huge and difficult to build.
5 Ways to Find Your Septic Tank
1. Check with the municipal records. The most straightforward method of locating your septic tank is to review the building plans for your home that were approved by the local government. You should have received an application from the business that installed the septic tank, which should contain schematics and specifications that will help you to locate the precise location where the septic tank was installed. 2. Look for highs and lows in your data. The majority of septic tanks are constructed in such a way that they are barely noticeable.
- Almost usually, your septic tank will be constructed near where the main sewage line exits your property.
- Septic tanks are typically positioned between ten and twenty-five feet away from a home’s foundation.
- When you do, that’s when your septic tank comes into play!
- Look for the Lid.
- You will most likely find two polyethylene or fiberglass covers positioned on opposing sides of the perimeter of your septic tank if it was built after 1975 and installed after 1975.
- Those areas should be excavated in order to disclose the lids.
- Get in touch with the pros.
- Lifting concrete lids will necessitate the use of specialized equipment.
- A fall into an unprotected septic tank has the potential to be lethal.
- Produce your own diagram of your yard, which you may file away with your other important house paperwork.
That’s all there is to it! If you’ve been wondering where your septic tank is, you now have five alternatives to choose from, which should make finding it easier than ever. To book a plumbing service in Bastrop County, please contact us now!
How to Find Your Septic Tank
Many folks have contacted me through e-mail (typically from across the nation) to inquire about the location of their septic tank. “I have no idea,” I generally say as a helpful response to the question. I really want to add something like, “It’s just off your driveway, near that bushy thing,” or anything along those lines. But, truly, even for the most experienced searchers, septic tanks are difficult to come by. The following are some strategies you might employ to assist you in locating your tank.
- Precaution should be exercised before you get started.
- So, proceed with caution!
- Please let me know if you have any queries or need assistance.
- Get to know the beast!
- tanks are normally buried 4 inches to 4 feet below the surface of the ground.
- You might be astonished to hear that someone knows exactly where it is hidden in plain sight.
- It is against the law to dig or probe in your own yard without first locating and marking the underground services.
You will receive the following tools to aid you in your search: Measurement tape, tile probe, and a shovel (if you are ambitious) The following tools are required: a metal detector (borrow or rent one since septic tanks often include iron steel rebar in the lids), and a hoagie sandwich (because locating sewage tanks makes you hungry.trust me on this).
- Examine the basement wall to see where all of the pipes join together and exit through the basement ceiling.
- If you don’t have a basement, walk outdoors and check for the roof vents on your house.
- Ordinarily, the sewage line that leads to the septic tank will exit the home right below this ventilation opening.
- On sometimes, the ancient proverb “The grass is always greener on the other side of the septic tank” is true.
Your tank may be located by probing or digging for it, and with luck, you will locate it. Keep in mind that not everything that seems to be a septic tank actually is! It’s possible that you came upon one of the following instead:
- Rubble buried in the ground (not to be confused with Barney Ruble)
- An old foundation
- In case you happen to live in a cemetery (which is spooky), you may use a grave vault to keep your belongings safe.
After a few hours of hopelessly digging about in your yard, it will be time to eat your hoagie and take a little sleep. Following that, it will be necessary to rent or borrow a metal detector. In the event that your next-door neighbor loves Star Wars action figures or has more than three unidentified antennae on his roof, there is a significant probability that you can borrow his metal detector. If you’re lucky, the metal detector will really assist you in finding your septic tank, rather than simply a bunch of old buried automobile parts.
According to local legend, a pumper known as “Zarzar The Incredible” can locate sewage tanks using a metal measuring tape spanning 30 feet in length.
Continue to press your commode (“commode” sounds sophisticated) tape deeper and farther down the pipes until he “feels” the bottom of the tank with his tape.
I recently acquired locate equipment that can be used to locate septic tanks, and I’m excited about it.
For further information, please contact me at 574-533-1470.
After that, you may have a movie of the inside of your sewer pipes created!
Related: Visit our Septic System Maintenance page for more information.
Services provided by Meade Septic Design Inc.
Both Clients and Projects are included.
Send me an email!
Looking for Your Septic Tank? Here’s How to Find It
“It’s 9 o’clock, do you know where your septic tank is?” says the interrogator. Maybe this is a little over the top, but it’s a question that many of our clients have asked over the years. In particular, new homeowners who are unfamiliar with the inner workings of their home or who haven’t needed septic tank servicing yet should be aware of the risks involved. Knowing where your septic tank is located is essential for routine maintenance and when you wish to add additional landscaping to your property.
Why you need to know where your septic tank is located
If your house does not have access to municipal sewage services, it is almost inevitable that you have a septic tank to redirect and store all of your wastewater someplace on your property’s subterranean drainage system. While a septic system is trustworthy and cost-effective, it does not operate without some kind of upkeep. According to the Environmental Protection Agency, a septic tank should be examined at least once every three years and drained every three to five years at the absolute least.
Another possibility is that there is an issue with the tank or its pipes. In either of these scenarios, you’ll need to know the location of your septic tank so that you can arrange for it to be serviced.
How to find your septic tank
- Inquire with your neighbors– If you have a septic tank, it’s possible that your neighbors have, too. Perhaps you’ll be fortunate enough to come across someone who knows where your tank is or who can assist you in narrowing down your search
- Obtain information from public records– It is possible that your local county or municipality has an existing septic tank map on file, which contains a schematic and the measurements of your property. Examine the home inspection report you received when you purchased your house to see if there is any mention of the presence of a septic tank and the location of the tank before going to your local records office. Start in the basement and discover the sewer pipe that leaves the house if you have to locate the tank by yourself. Pipe with a diameter of four inches is usual for this application. After that, go outside and around to the opposite side of the wall. Then, using a metal soil probe to poke small holes in various locations around your property, trace the pipe’s course until you reach the tank. When you strike the flat top surface of the tank with the probe, you’ll notice a distinct change. Consider your surroundings– If you have a huge property, locating a needle in a haystack might seem like a daunting task. To make your search more efficient, you can eliminate locations near structures, paved surfaces, the water well, and, ideally, regions with extensive trees or landscaping from consideration. Another possibility is that you may notice a patch of grass that is a little greener or that is growing more quickly around the tank. Locate the septic tank lid– Regardless of how you pinpoint the position of the tank, you may need to perform a little digging in order to expose the lid. You may use the soil probe to determine the perimeter of the tank – most tanks will be around 5 7 feet in length and width. As soon as you’ve outlined the edges, start shoveling in the middle and working your way around the perimeter until you reach the lid. However, unless you’re servicing the tank immediately away, there’s no reason to lift the top and let the noxious odors out into the environment.
After you’ve located your septic tank, make a note of the position on a map or mark it on your GPS device for future reference. This will assist you in avoiding the construction of structures or the planting of deep-rooted plants in the vicinity of the sewage line and septic tank. When it comes to selling your house, a map or handwritten diagram may also be beneficial. If you want plumbing assistance in New Haven or Fairfield County, Rick’s Plumbing is the brand you can rely on. In order to obtain expert assistance, please send us a message or phone us at (203) 874-6629.
- The post was published on July 16, 2019 under the category Septic Tank System.